Project tutorial

Rangefinder for Garage Parking with Arduino © GPL3+

Park your car safely in the garage with Arduino!

  • 3,779 views
  • 1 comment
  • 13 respects

Components and supplies

A000057 featured
Arduino Leonardo
×1
Matrix display
(find it on internet stores)
×1

Necessary tools and machines

09507 01
Soldering iron (generic)

About this project

This simple project will help you park your car in the garage by displaying the distance from objects in front of your car's bumper. A 'stop' message will tell you when it's time to stop. The project is based on the usual HC-SR04 or Parallax Ping))) (tm) ultrasonic rangefinders and an Arduino board. I used the Leonardo but it should work on any other original or compatible board.

For the display I chose a matrix version for its size and for aesthetic reasons.

Step 1: What You Need...

To build this project you need:

  • An Arduino board:An original or compatible board should work as the code doesn't make use of specialized pins/function.You can find it everywhere on the internet or maybe you have one unused in a drawer in your lab.
  • Soldering skills, of course :)

Step 2: Build the Project...

Download the arduinorangefinder.pdf schematic diagram.You can find attached also the HC-SR04 pdf and the ping))) pdf, only for your reference.The electronic diagram is very simple, follow it exactly.I suggest to extend the wirings for the display and sensor of about 1 meter (see image1) so you can place them more easily later.

In the image2 you can see how to solder the power supply pins for the display and sensor: +5V from the display and Vcc from the sensor needs to be soldered togheter. Every other pin must have its own terminal.

Image5 is the Ping))) version of the project.Go to the next step when ready...

Step 3: Arduino Code...

It's time to work on the Arduino side.

Download the attached fourMatrix-master library (please use this library also if you already have it installed, this one was edited to support more functionalities) and install it from the IDE (sketch->import library).

Now load the MeasureDistanceV101.ino sketch and let's look into it, there are several lines you can edit:the most important is the sensor type, uncomment only the line that match your sensor.

Then set the distances as you prefer, you can modify them later when the project will be in place.

Upload the code and check if all works.If you get trouble please double check wirings and connections.

Update 2017/12/30:The code has been updated to turn off the display when standstill at STOP distance for more than 10 seconds!

Step 4: The Project at Work...

Measure the height of the most prominent part of the bumper of your car from the floor.Attach the sensor close to the wall, to the height you measured.

I used a polystyrene foam sheet in which I made a slot for the sensor (see image).

Now place the display so you can see it from your car.

Try to enter by car and check the distances, adjust them in the Arduino code and reupload it if need.

Enjoy!

Comments

Similar projects you might like

PENXZYL: Arduino 3-Axis Brush Plotter

Project showcase by Guiye Perez Bongiovanni

  • 3,668 views
  • 2 comments
  • 15 respects

MyRiver

Project tutorial by Andrei Florian

  • 8,557 views
  • 2 comments
  • 35 respects

Detecting Heart Rate with a Photoresistor

Project tutorial by 3 developers

  • 6,716 views
  • 3 comments
  • 18 respects

Weather Forecast Clock Using Old Alarm and Arduino

Project showcase by LenkaDesign

  • 4,145 views
  • 10 comments
  • 23 respects

Photoresistor Characterization

by 3 developers

  • 2,201 views
  • 4 comments
  • 6 respects

u-blox LEA-6H 02 GPS Module with Arduino and Python

Project tutorial by Harshgosar

  • 1,351 views
  • 7 comments
  • 5 respects
Add projectSign up / Login