Project in progress
Arduino Long Range Explorer Tank KureBas V3.0 (HC-12 1.8 KM)

Arduino Long Range Explorer Tank KureBas V3.0 (HC-12 1.8 KM) © GPL3+

Let's Test Hc-12 Bluetooth module that have 1.8 km range.

  • 1,589 views
  • 2 comments
  • 16 respects

Components and supplies

Apps and online services

About this project

Watch ...

Code

Kurebas V3.0 Base CodeC/C++
---------------------------RECIEVER PART-------------------------------------


#define enA 9
#define in1 4
#define in2 5
#define enB 10
#define in3 6
#define in4 7
int xAxis, yAxis;
int  x = 0;
int  y = 0;
int motorSpeedA = 0;
int motorSpeedB = 0;
void setup() {
  pinMode(enA, OUTPUT);
  pinMode(enB, OUTPUT);
  pinMode(in1, OUTPUT);
  pinMode(in2, OUTPUT);
  pinMode(in3, OUTPUT);
  pinMode(in4, OUTPUT);
  Serial.begin(9600); // Default communication rate of the Bluetooth module
}
void loop() {
  // Default value - no movement when the Joystick stays in the center
  xAxis = 510;
  yAxis = 510;
  // Read the incoming data from the 
  while (Serial.available() == 0) {}
  x = Serial.read();
  delay(10);
  y = Serial.read();
  delay(10);
  // Convert back the 0 - 255 range to 0 - 1023, suitable for motor control code below
  xAxis = x * 4;
  yAxis = y * 4;
  // Y-axis used for forward and backward control
  if (yAxis < 470) {
    // Set Motor A backward
    digitalWrite(in1, HIGH);
    digitalWrite(in2, LOW);
    // Set Motor B backward
    digitalWrite(in3, HIGH);
    digitalWrite(in4, LOW);
    // Convert the declining Y-axis readings for going backward from 470 to 0 into 0 to 255 value for the PWM signal for increasing the motor speed
    motorSpeedA = map(yAxis, 470, 0, 0, 255);
    motorSpeedB = map(yAxis, 470, 0, 0, 255);
  }
  else if (yAxis > 550) {
    // Set Motor A forward
    digitalWrite(in1, LOW);
    digitalWrite(in2, HIGH);
    // Set Motor B forward
    digitalWrite(in3, LOW);
    digitalWrite(in4, HIGH);
    // Convert the increasing Y-axis readings for going forward from 550 to 1023 into 0 to 255 value for the PWM signal for increasing the motor speed
    motorSpeedA = map(yAxis, 550, 1023, 0, 255);
    motorSpeedB = map(yAxis, 550, 1023, 0, 255);
  }
  // If joystick stays in middle the motors are not moving
  else {
    motorSpeedA = 0;
    motorSpeedB = 0;
  }
  // X-axis used for left and right control
  if (xAxis < 470) {
    // Convert the declining X-axis readings from 470 to 0 into increasing 0 to 255 value
    int xMapped = map(xAxis, 470, 0, 0, 255);
    // Move to left - decrease left motor speed, increase right motor speed
    motorSpeedA = motorSpeedA - xMapped;
    motorSpeedB = motorSpeedB + xMapped;
    // Confine the range from 0 to 255
    if (motorSpeedA < 0) {
      motorSpeedA = 0;
    }
    if (motorSpeedB > 255) {
      motorSpeedB = 255;
    }
  }
  if (xAxis > 550) {
    // Convert the increasing X-axis readings from 550 to 1023 into 0 to 255 value
    int xMapped = map(xAxis, 550, 1023, 0, 255);
    // Move right - decrease right motor speed, increase left motor speed
    motorSpeedA = motorSpeedA + xMapped;
    motorSpeedB = motorSpeedB - xMapped;
    // Confine the range from 0 to 255
    if (motorSpeedA > 255) {
      motorSpeedA = 255;
    }
    if (motorSpeedB < 0) {
      motorSpeedB = 0;
    }
  }
  // Prevent buzzing at low speeds (Adjust according to your motors. My motors couldn't start moving if PWM value was below value of 70)
  if (motorSpeedA < 70) {
    motorSpeedA = 0;
  }
  if (motorSpeedB < 70) {
    motorSpeedB = 0;
  }
  analogWrite(enA, motorSpeedA); // Send PWM signal to motor A
  analogWrite(enB, motorSpeedB); // Send PWM signal to motor B
}



------------------------------------TRANSİVER PART------------------------------


int xEkseni, yEkseni;
void setup() {
  Serial.begin(9600); // Default communication rate of the Bluetooth module
}
void loop() {
  xEkseni = analogRead(A0); // Read Joysticks X-axis
  yEkseni = analogRead(A1); // Read Joysticks Y-axis
  
  // Send the values via the serial port to the slave HC-05 Bluetooth device
  Serial.write(xEkseni/4); // Dividing by 4 for converting from 0 - 1023 to 0 - 256, (1 byte) range
  Serial.write(yEkseni/4);
  delay(20);
}

Schematics

verici_hod9u56MCt.png
Verici hod9u56mct
alici_cD6JdNF9MX.png
Alici cd6jdnf9mx

Comments

Similar projects you might like

Solar Panel Sun Tracker - Phone Charger

Project tutorial by FIELDING

  • 27,320 views
  • 11 comments
  • 119 respects

DIY 3-Axis CNC VMC

Project tutorial by Amit Nandi (BigWiz)

  • 12,163 views
  • 9 comments
  • 46 respects

Android Controlled 6DoF Robotic Arm

Project in progress by Team Mans

  • 11,065 views
  • 0 comments
  • 17 respects

Arduino Colored OLED

by RoboCircuits

  • 3,655 views
  • 1 comment
  • 16 respects

Smartphone Controlled Arduino 4WD Robot Car

Project in progress by Andriy Baranov

  • 53,321 views
  • 43 comments
  • 98 respects

Simple Programmable Robotic Arm

Project showcase by Ryan Chan

  • 49,017 views
  • 63 comments
  • 145 respects
Add projectSign up / Login