Attiny85/84 with Bluetooth © GPL3+

Attiny85/84 is very small and powerful chip from Atmel. In this tutorial we can add Bluetooth capabilities to this micro controller.

  • 11,954 views
  • 0 comments
  • 51 respects

Components and supplies

Apps and online services

About this project

Here I have used HC -05 bluetooth module which can be purchased from ebay at a very low cost.eto Attiny85/84 .In this tutorial I won't be going in detail about how to upload the sketchs to Attiny85/84. I also hope that you are familiar with arduino and bluetooth concepts If no you can accept google as your teacher.

Setup

Here in this tutorial I will show you how to start serial communication with the ATiny85 over a Bluetooth network. First upload the following sketch to Attiny85. Make sure that you burn 8mz boot loader to Attiny before uploading the sketch.

Knowing your Bluetooth Connection

Here I have used HC -05 bluetooth module which can be purchased from ebay at a very low cost. Refer the following image to identify the pin diagram of Hc-05 module.

Now connect the Attiny 85 to Hc-05 module as given below.

  • Bluetooth Module Rx --> ATiny85 Pin 1
  • Bluetooth Module Tx --> ATiny85 Pin 2
  • Bluetooth Module Gnd --> ATiny85 GND
  • Bluetooth Module VCC --> ATiny85 VCC
  • LED pin -->ATiny85 Pin4

Getting it all Connected

Connect every Attiny85 as shown above .Now to check weather the serial communication works between bluetooth module and Attiny85 download the apk(Dime.apk) file provided in the attachment. This app was made by using MIT App inventor. You too can edit this I have attached an aia(Dime.aia) file below.

How to use the Bluetooth App?

Make sure that the Attiny and bluetooth is powered .

Open the app then click on the bluetooth icon in the app and select the HC-05 from the list.(Before connecting you have to make sure that HC-05 is paired with the mobile).Once the HC-05 is connected the text will show as"Connected".

Now shake your phone and see that the led blinks. You can even use a relay instead of led and control the home appliances.

Comments and Questions welcome! Thanks for reading.

Code

Attiny Bluetooth program.C/C++
#include <SoftwareSerial.h>  //Software Serial Port
#define RxD 1
#define TxD 2

#define DEBUG_ENABLED  1
 
SoftwareSerial blueToothSerial(RxD,TxD);

int led = 4;
 
void setup() 
{ 
  pinMode(RxD, INPUT);
  pinMode(TxD, OUTPUT);
  setupBlueToothConnection();
  
  pinMode(led,OUTPUT);
  digitalWrite(led,HIGH);
 
} 
 
void loop() 
{ int count=0;
  char recvChar;
  while(1){
    //check if there's any data sent from the remote bluetooth shield
    if(blueToothSerial.available()){
      recvChar = blueToothSerial.read();
      count++ ;
        if(count%2==0)
          digitalWrite(led,HIGH);  
       
        else
          digitalWrite(led,LOW); 
    }
  }
} 
 
void setupBlueToothConnection()
{
  blueToothSerial.begin(9600); //Set BluetoothBee BaudRate to default baud rate 38400
  blueToothSerial.print("\r\n+STWMOD=0\r\n"); //set the bluetooth work in slave mode
  blueToothSerial.print("\r\n+STNA=HC-05\r\n"); //set the bluetooth name as "HC-05"
  blueToothSerial.print("\r\n+STOAUT=1\r\n"); // Permit Paired device to connect me
  blueToothSerial.print("\r\n+STAUTO=0\r\n"); // Auto-connection should be forbidden here
  
  delay(2000); // This delay is required.
  //blueToothSerial.print("\r\n+INQ=1\r\n"); //make the slave bluetooth inquirable 
  blueToothSerial.print("bluetooth connected!\n");
  
  delay(2000); // This delay is required.
  blueToothSerial.flush();
}

Custom parts and enclosures

This is the apk file of the app featured in the tutorial.
Dime.apk
Dime.aia
Dime.aia

Schematics

ATtiny bluetooth connection
ATtiny85with%20bluetooth.fzz
Programmer_for_ATtiny85_with_arduino (1).fzz
Programmer_for_ATtiny85_with_arduino%20(1).fzz
This the apk file of the app featured in the tutorial.
Dime.apk

Comments

Similar projects you might like

Arduino Bluetooth Basic Tutorial

by Mayoogh Girish

  • 455,028 views
  • 42 comments
  • 239 respects

Home Automation Using Raspberry Pi 2 And Windows 10 IoT

Project tutorial by Anurag S. Vasanwala

  • 285,525 views
  • 95 comments
  • 671 respects

Security Access Using RFID Reader

by Aritro Mukherjee

  • 229,469 views
  • 38 comments
  • 238 respects

OpenCat

Project in progress by Team Petoi

  • 196,048 views
  • 154 comments
  • 1,363 respects
Add projectSign up / Login