Project tutorial
Arduino Automated Parking Garage

Arduino Automated Parking Garage © GPL3+

A fully automated smart car parking system- powered using just a power bank!!!

  • 8,719 views
  • 11 comments
  • 27 respects

Components and supplies

Apps and online services

About this project

An Arduino Automated Car Parking System that is too easy and too fun to make. When a car arrives it shows the number of empty slots (if available) and then opens the gate. if there is not any empty slot then the gate does not open. Amazing thing is that the whole project can just be POWERED using a POWER BANK!!

Watch the video for the full tutorial.

Note: you can use display instead of my hand made led sign display.

Now lets get started.

Step 1: Parts

  • Arduino - any board
  • Infrared proximmity sensor (pic 2 & 3 - both are functional)
  • 330r resistor
  • some LED's
  • Servo motor - any model or size you wish.

Step 2: Making the LED Display

To make this LED display I have used a piece of bredboard then soldered the LED's and the 330r resistor. Then just added a ribbon cable for nice finish.

NOTE: I soldered the resistors on back so that they cant be seen from front to make the display.

It would be better if you use LCD display or cheap OLED display instead of this. I had not any, so I made this.

Step 3: Making the Parking Garage

To make this I have used a card board box then cut it to make a nice slope. Then added a piece of cardboard on to the servo motor and hot glued it. Added one sensor on the entrance and another on each SLOT. Then hot glued two chopsticks with the display we have made and glue it to the box. And of course as we will use the usb cable of arduino to power the whole project cut some area of the box to access to that port.

Don't forget to paint it a little bit.

Step 4: The Circuit

It looks a bit mess for the LED's but tell you what, this is really very much simple circuit.

NOTE: Proximity sensors use 5v to operate so you can just connect them to 5v source of arduino.

But what theee!! why has he connected servo to VIN!! Let me explain you. Power banks usually supplies 5v 1Amp current which is input to arduino via the usb cable, now there is a voltage regulator on arduino which gives.5Amp to the board. By connecting to VIN we are actually accessing the power from the power bank without an breadboard. This works and safe.

Step 5: The Code

Upload the following code to the arduino

download code https://github.com/ashraf-minhaj/Automated-Parking...

or copy CODE from below

Step 6: Finished

Now power the project using a USB cable to arduino and have fun.

Let me know how you are thinking to upgrade this and why.

Thank you.

Code

automated parking garage,code.ashrafminhajC/C++
/*Automated Parking Garage by Ashraf Minhaj. www.youtube.com/c/fusebatti
 * for any query please mail me at ashraf_minhaj@yahoo.com*/

#include<Servo.h>   //adding Servo library
Servo gate;        //you may open or close gate using a Servo motor
int slot1 = 5;   //Connect IR sensor on digital pin5 for sLOT 1
int slot2 = 4;   //sLot2 pin on digital 4 
int gateSensor = 3; //IR sensor on gate to arduino pin 3
int slot1_l = 13;
int slot2_l = 12;
int gate_grn = 11;
int gate_red = 10;


void setup() 
{
 gate.attach(7);     //connecting the gate servo on pin 5
 pinMode(slot1,INPUT);  //setting slot pins  & gate IR sensor as input to arduino
 pinMode(slot2,INPUT);
 pinMode(gateSensor,INPUT);
 pinMode(slot1_l,OUTPUT);
 pinMode(slot2_l,OUTPUT);
 pinMode(gate_grn,OUTPUT);
 pinMode(gate_red,OUTPUT);
 Serial.begin(9600);       //initialzing Serial monitor

}

void loop() 
{
     //the car arrives and sensor goes LOW

    if(   !(digitalRead(gateSensor)) && digitalRead(slot1) && digitalRead(slot2))   //slot1 & slot2 empty
     {
      Serial.println("Welcome, Available: sLOT1, sLOT2");  //print slot1 and slo2 available
      digitalWrite(slot1_l,HIGH);
      digitalWrite(slot2_l,HIGH);
      delay(1000);
      digitalWrite(gate_grn,HIGH);
      gate.write(75); //gate will open after the dealy of 1 second
     }

     if( !(digitalRead(gateSensor)) && !(digitalRead(slot1)) && digitalRead(slot2))  //car on slot1,slot2 free
      {
          Serial.println("Welcome, Available: sLOT2");  // slo2 available
          digitalWrite(slot1_l,LOW);
          digitalWrite(slot2_l,HIGH);
          delay(1000);
          digitalWrite(gate_grn,HIGH);
         gate.write(75); //gate will open after the dealy of 1 second
      }
      
       if( !(digitalRead(gateSensor)) && digitalRead(slot1) && !(digitalRead(slot2)))     //car on slot2,slot1 free
       {
         Serial.println("Welcome, Available: sLOT1");  // slo1 available
          digitalWrite(slot1_l,HIGH);
          digitalWrite(slot2_l,LOW);
          delay(1000);
         digitalWrite(gate_grn,HIGH);
         gate.write(75); 
          delay(100);                //gate will open after the dealy of 1 second
       }
      

        if( !(digitalRead(gateSensor)) && !(digitalRead(slot1)) && !(digitalRead(slot2)))
         {
           Serial.println("Welcome, Parking Full");// No slot available
            digitalWrite(slot1_l,LOW);
            digitalWrite(slot2_l,LOW);
            delay(1000);
            digitalWrite(gate_red,HIGH);
            delay(100);
            digitalWrite(gate_red,LOW);
            delay(100);
            digitalWrite(gate_red,HIGH);
            delay(100);
            digitalWrite(gate_red,LOW);
            
            
         }
            
  if( digitalRead(gateSensor))    // no input detected
        { Serial.println("Welcome");  
          gate.write(5);       //gate close
         digitalWrite(slot1_l,LOW);
         digitalWrite(slot2_l,LOW);
         digitalWrite(gate_red,LOW);
         digitalWrite(gate_grn,HIGH); //gate grin or yellow light will blink
         delay(100);
         digitalWrite(gate_grn,LOW);
         delay(100);
         
        
        }
  
}

Schematics

automated parking garage
Automated parking garage tzqh7wof48

Comments

Similar projects you might like

Automated Parking Lot System

by 송민지

  • 3,162 views
  • 1 comment
  • 11 respects

Garage Parking Stop Light

Project showcase by Rich Noordam

  • 2,444 views
  • 0 comments
  • 10 respects

Parking Sensor with Arduino

Project showcase by Team VINICIUS LOPES

  • 9,934 views
  • 4 comments
  • 17 respects

SunGlass-BOT [An Automated Pair of Sunglasses]

Project tutorial by ashraf_minhaj

  • 8,695 views
  • 6 comments
  • 16 respects

Garage Parking Sensor

Project tutorial by Chip McClelland

  • 8,114 views
  • 5 comments
  • 14 respects

Arduino Trash-Bot (Auto-Open/Close Trash Bin)

Project tutorial by ashraf_minhaj

  • 2,796 views
  • 3 comments
  • 12 respects
Add projectSign up / Login