Project in progress

Vertical Hydroponic Farm © CC BY-NC-SA

IoT Enabled Hydroponic Farm

  • 49,783 views
  • 20 comments
  • 260 respects

Components and supplies

About this project

We call our project RUFS, for Robotic Urban Farm System

  • A vertical hydroponic garden
  • Allowing for high density yields and shorter growth cycles
  • Reducing resource consumption - water, fertilizer and space
  • Labor saving - no weeds or soil to till
  • Higher consistency of crops with great tasting results
  • Maintained by micro-controllers (Raspberry Pi & Arduino)
  • Watering cycles - monitor and auto refill levels
  • Plant nutrients and pH - monitor and correct
  • Temperature monitoring
  • Air Circulation & Lighting controls (for indoor operation)
  • Smart and Connected
  • Farm Controller App for smartphone, tablet and pc
  • Get notified when the system needs a refill
  • Alerts when something isn't running as expected
  • Year round growing - fresh produce every month of the year
  • Perfect for Urban setting with limited space
  • Reduced operational time and maintenance with automation
  • Eliminate the guesswork of nutrients and watering cycles

Hydroponics is a subset of hydroculture and is a method of growing plants using mineral nutrient solutions, in water, without soil.

The word hydroponics technically means working water, stemming from the Latin words "hydro" meaning water, and "ponos" meaning labor. Many different civilizations from the beginning of time have relied on hydroponics for growing plants, such as the early Mexican and Egyptian civilizations. However, recently growing hydroponically has grown in popularity and use across many different markets.

(from Wikipedia http://en.wikipedia.org/wiki/Hydroponics)

Green and Efficient

Water is recirculated which allows for great efficiency, often more than 90% efficiently on water consumption.

Our vertical design allows for a higher density of plants in a much smaller footprint. With a space less than 5' x 5' we are growing 160 plants.

Automation

The system is maintained with a series of Arduino controllers. Watering cycles, pH levels, nutrient levels, lighting cycles and ventilation fans are all maintained via the Arduino's.

The Arduino's can be networked to a Raspberry Pi using I2C to allow all system parameters to be monitored and updated in real time. The Raspberry Pi is further used to maintain a historical log of all the systems running data and make it available via a set if web services.

A companion smartphone/tablet app interfaces with the Raspberry Pi allowing for configuring and monitoring your entire system from anywhere in the world. The Raspberry Pi communicates with app via a JSON web service.

What are we growing?

Vertical hydroponics lends itself very well to leafy green vegetables.I am currently growing successfully lettuces (romaine, boston bib, spring mix) , cabbages (red and green), herbs (basil, cilantro, mint, dill, chives), spinach, kale (dwarf curly variety), broccoli and petunias.

------------

Parts and Pieces (What to buy)

Support Frame

(5) 10' - 2" PVC pipe

(1) 10' - 3" PVC pipe

(4) 2" PVC 90° elbow

(8) 2" PVC tee

(4) 3" to 2" PVC tee

(4) 3" PVC endcaps

Note: All PVC pipe and fittings are Schedule 40 - cellular PVC

Towers/Return

(10) 10' - 2" x 3" PVC downspouts

(1) 10' PVC extruded gutter 4"

(4) PVC gutter end caps (make sure to get 2 left and 2 right)

(2) 1" threaded to 3/4" barbed adapter

(2) 3/4" PVC female threaded connectors

(20) 2" PVC Pipe Hangers ("J" hooks)

(20) #6 Stainless 1 1/2 " machine screws and nuts

Water Supply/Return

(1) 10' - 1"ID potable water tubing

(3) 1" threaded to 3/4" barbed adapter

(1) 1" barbed tee

(5) 3/4" PEX 90° elbow - barbed

(1) 3/4" PEX tee - barbed

(1) 1" to 3/4" PEX reducer - barbed

(2) 10 pack PEX crimp rings

(1) 10 pack 1 1/2" hose clamps

(1) 25' - 3/4" PEX

(20) adjustable 0-10GPH drip emitters

(1) 14 gallon soft plastic bucket

Support Frame (See pictures for steps)

The support frame is constructed from standard Schedule 40 PVC in 2" and 3" OD(outer diameter). The frame was constructed from this material for is modular properties (easy to fit together) and the ease of use for sizing (easy to cut straight with basic tools). This does not preclude the use of other structural material such as wood, plastic and metal as the frame is structural and does not carry water.

Tool note:

PVC pipe for this project is best cut using a mitre saw. These are readily available as an inexpensive hand tool or an electric/power tool. A mitre saw provides good 90° cuts that help add to the stability of the frame.

PVC is glue using a two part glue system.

An Oscillating Multifunction Power Tool was used to cut pockets in vertical towers.

An Electric Heat Gun was used to shape the pockets in the vertical towers.

The support frame is (2) main leg components joined by the (2) "top bar" components and (2) "cross supports".

The length of the "top bar" and "cross supports" dictate the capacity of the towers your system will support.

There are two additional leg extensions made from the 3" PVC that can provide addition support against the elements when used outside. These can be omitted for indoor use.

At 4' we are supporting (10) grow towers spaced at 4.5" on center apart.

Support Top

The top support dictates the size of the grow system and the number of towers the system can support.

Our current plan includes a 4' length of 2" PVC with towers spaced at 4.5" on center. The spacing can be modified to support larger growing areas by increasing spacing between the centers of the towers.

Additional you can decrease the length of pipe to support a smaller number of grow towers.

The support top structure are (2) identically constructed units.

Support Top Cut List

  • From a 10' section of 2" PVC
  • Cut (2) sections at 48" - (these are Part #1 - first & second set)

Support Top Assembly Instructions

Dry fit the following:

  • Fit 2" pipe Part #1 into (2) Part #2 90° elbow

Support Bottom

Like the top support, the bottom cross dictates system size, the piece must be the same width as the support frame top.

Our current plan includes a 4' length.

The support bottom piece are (2) identically 4' sections.

Also included in the bottom of the frame are (2) optional extension legs that are good when the unit is set up outside to provide additional support against wind.

Support Bottom Cut List

  • From a 10' section of 2" PVC
  • Cut (2) sections at 48" - (these are Part #1 - first & second set)
  • From the remaining section of 3" PVC
  • Cut (4) sections at 12" - (these are Part #2)

Support Top Bottom Instructions

Dry fit the following:

  • Fit 2" pipe Part #1 into the Part #6 90° tee of the main leg component
  • Note:You man need an additional person to help hold up the legs when installing bottom cross pieces
  • Optional: Fit 3" pipe Part #2 into the Part #9 90° tee of the main leg component
  • Optional: Install cap Part #3 into the 3" pipe Part #2

Grow Towers/Water Return

The towers provide the grow area for the plants in this system.

Or current design supports a very high density of plants by spacing the 3" vertical grow towers 4.5" apart on center (distance from center of tower to neighboring tower), providing approximately 1.5" between towers.

The current 4' length supports (10) towers with (8) slots per tower. With two sides we get (160) plants for our entire system.

There are some limitations to this high density and vertical grow systems to the types of plant you can grow.

Towers/Return Overview

The towers are 2" x 3" PVC modified downspouts. The downspouts are generally available in 10' sections.

The availability of 10' sections dictated the 5' height of our design.

The water returns are 4" PVC rain gutters. Also available in 10' sections. They are cut and capped on the ends with gutter caps. Make sure you pick up both left and right versions of the end caps as they are different.

Towers/Return Construction Steps

Part 1: Towers

Towers Cut List

  • From a 10' sections of 2" x 3" PVC downspouts
  • Cut (10) sections in half at 60"

Tower Shaping Instructions

We constructed a wood template tool to help form the plant pockets

  • Divide the (20) towers in to (2) sets of (10).
  • To improve grow space we offset/stagger the plant slots in the grow towers.
  • Mark a horizontal line across the front of the first set of (10) towers every 6" starting 6" from the bottom for (8) lines.
  • A speed square is helpful and getting a straight line across the down spout material.
  • Mark a horizontal line across the front of the first set of (10) towers every 6" starting 9" from the bottom for (8) lines.
  • Using a Oscillating Multifunction Power Tool with the straight cut bit, cut a 2" slice on the drawn lines.
  • Using the Electric Heat Gun soften the plastic for a few seconds (approx. 15-30 seconds depending on wattage of your heat gun) 3" above and 3" below the cut. The PVC will start to pucker or sink and takes on the appearance of wet saggy paper.
  • Use your wood template to slide into the softened PVC at the cut. Hold in place for approximately 30 seconds.
  • Repeat for remaining slots in the tower.
  • Drill a 3/16" hole on the top, back side of the tower to put the screw for the tower hanger.

Water Return

Water Return Cut List

  • From a 10' sections of 4" PVC gutters
  • Cut (4) sections at 46"

Water Return Assembly Instructions

  • Identify the right and left gutter end caps.
  • Test fit end caps on the sections of gutter.
  • We roughed up the gutter plastic with some 150 grit sandpaper where the caps overlap the gutter (about 5/8") for a better adhesion.
  • Spread a liberal bead of silicone PVC adhesive on the inside overlapping edge of the end caps.
  • Carefully fit the end cap on the gutter making sure glue contacts all around the gutter material.
  • We used our finger to push excess adhesive around the edge of the gutter and cap to ensure good contact.
  • Place a piece of masking tape or other easily removable tape on the cap till the recommended dry time.
  • Repeat for other 3 sides and set aside till dry.
  • Drill a 1" hole on the back wall of the 4" gutter to insert 1" to 3/4" barbed adapter. This will serve as the connector for the water return to the 14 gallon bucket.
  • Thread the 1" threaded side of the adapter and thread into the female 1" connector on the inside of the gutter.
  • Cut a (2) - 12" section of soft 1" vinyl hose for each side of the water return.
  • Join at the center with the 1" barbed tee.
  • Cut a section of vinyl tube to length to where you position your 14 gallon water tank.

Water Supply

We choose 3/4" PEX for the main water supply lines for it's potable water safety properties and the ease of installation because we had a PEX crimp installation tool. CPVC would also be an excellent choice if the crimp tool was not available, CPVC is also certified for potable water but requires glue and joint connectors for assembly.

Water Supply/Return Overview

The water supply is laid out so there is a single rise that forks at the center cross piece of the main leg. This design was implemented to reduce the overall height load on the water pump. Instead of (2) 6' rises reducing overall water flow, the rise is slightly more efficient to the pump.

Water Supply/Return Construction Steps

  • Parts #1 - #6 are 3/4" PEX cut to mirror the main leg dimensions.
  • These are best sized by taking the measurements of the legs.
  • Crimp Part #1, Part #2 and Part #3 together with Part #7 - 3/4" barbed PEX tee.
  • Crimp Part #3 and Part #4 together with Part #8 - 3/4" PEX 90° elbow.
  • Crimp Part #4 and Part #5 together with Part #9 - 3/4" PEX 90° elbow.
  • Crimp Part #2 and Part #6 together with Part #10 - 3/4" PEX 90° elbow.
  • Drill holes in Part #5 and Part #6 for Part #11 - drip emitters.
  • Starting at elbow end of Part #5/Part #6 - measure from end 4" and mark first hole at the bottom of the PEX pipe.
  • It is helpful to draw a line along the bottom of the PEX pipe marking the bottom for the remaining marks.
  • Measure 4.5" from first mark and make a second mark.
  • Repeat every 4.5", the last mark should be 4" from the opposing leg from the elbow.
  • Using 3/16 drill bit drill on the mark.
  • Fit in the the drip emitters - Part #11
  • The hole is slightly snug for the drip emitters to prevent unwanted dripping, soften the PEX briefly (30 sec.) with the heat gun, this will allow for easier insertion of the drip emitters into the PEX.
  • Cut a 1" hole in the 14 gallon water bucket.
  • Thread the 1" to 3/4" barbed adapter through the wall of the water container.
  • Attach the soft vinyl hose from the return gutters tee to the water bucket.

Electronics

We broke the functionality of the controllers up into separate components.

ClimateBot

Role: Environmental controls for indoor operation.

Used to maintain light cycles based on schedule of on/off intervals and a thermostatically and/or schedule based control of a circulation fan.

Hardware Components

(1) Arduino

(1) 2 Channel Relay Module Board and Shield For Arduino (source: eBay)

(1) Circulation Fan sized to your space

(1) 15 Meter - LED based - 12v Flexible 5050 5:1 Red/Blue (source: eBay)

(1) Waterproof DS18B20 Digital Temperature Sensor Probe for Arduino (source:eBay)

pHarmBot

Role: Water quality control

Used to maintain pH level maintenance and nutrient level maintenance.

Hardware Components

(1) Arduino

(1) 2 Channel Relay Module Board and Shield For Arduino

(1) Analog pH Meter Kit (source: RobotMesh.com)

(1) Arduino Conductivity Sensor (source: eBay)

(1) Waterproof DS18B20 Digital Temperature Sensor Probe for Arduino (source:eBay)

(2) 12V DC Peristaltic Dosing Pump (source: Amazon)

hydroBot

Role: Watering cycles based on schedule of on/off intervals and water reservoir level maintenance

(1) Arduino

(1) 2 Channel Relay Module Board and Shield For Arduino

(2) Side Mounted Water Level Control Float Switch Normal Closed (source:eBay)

(1) 1" Water Flow Meter Counter 1-60L/min (source: Amazon)

(1) 1/2" DC 12V Electric Solenoid Valve Water Inlet Flow Switch Normally Closed (source: eBay)

(1) 620 GPH Submersible Pump (source: Harbor Freight)

Arduino Resources (Sketches and Links):

DS18B20 Digital Temperature Sensor Probe - See attached document (OneWire.txt)

http://playground.arduino.cc/Learning/OneWire

Arduino Conductivity Sensor - See attached document (EC_Sensor.txt)

Analog pH Meter - See attached document (ph_Meter.txt)

analog-ph-meter-kit

Custom parts and enclosures

Schematics

ClimateBot
A1
pHarmBot
A2
hydroBot
A3

Comments

Similar projects you might like

Lightpipe 7-Segment Display

Project tutorial by Brian Lough

  • 2,312 views
  • 3 comments
  • 6 respects

ElBanquos 1D Pong

Project showcase by ElBanquo

  • 149 views
  • 2 comments
  • 2 respects

Arduino Spider Robot (Quadruped)

Project tutorial by MEGA DAS

  • 1,970 views
  • 1 comment
  • 14 respects

PENXZYL: Arduino 3-Axis Brush Plotter

Project showcase by Guiye Perez Bongiovanni

  • 4,429 views
  • 4 comments
  • 20 respects

Google Chrome Dinosaur Game on 16x2 LCD Shield

Project showcase by brzi

  • 346 views
  • 1 comment
  • 7 respects

MyRiver

Project tutorial by Andrei Florian

  • 9,450 views
  • 2 comments
  • 36 respects
Add projectSign up / Login