MyAdafruit Neopixel Ring With 12 LEDs - Unboxing

MyAdafruit Neopixel Ring With 12 LEDs - Unboxing © GPL3+

First experience with Neopixel.

  • 6,381 views
  • 0 comments
  • 9 respects

Components and supplies

Apps and online services

About this project

Today, I share my experience of my first purchase of Adafruits Neopixel Rings with 12 pixels (= number of LEDs): The delivery came without a manual in a simple bag. I had decided to buy a cheap ring, so I would not be disappointed in the case of a defect, but the pixels made me smile quickly in the face.

Step 0: Wiring

I used crocodile clips and did not use a breadboard.

  • Close GND first (my black cable). On the back you find the names.
  • Data input is usually linked to PIN 6 (my yellow cable) and the pixels are supplied
  • with 5V + DC (my red cable).

Other steps

To my great pleasure are no further, additional components like MOSFETs (you can check out my LED project with MOSFETs) necessary.

  • Step 2: import Adafruits Neopixels Libary into your project
  • Step 3: look for a sample code - like the attached from and
  • Step 4: flash to your device.

Can´t upload my videos to hackster - so you can´t see my smile in the face.

Update: visit my Neopixel Ring 12 project to make a easy Light-Clock.

You will find more under my account.

Code

Original Libary from Adafruit with change in row 16: set the number of pixels in strip to 12C/C++
#include <Adafruit_NeoPixel.h>
#ifdef __AVR__
  #include <avr/power.h>
#endif

#define PIN 6

// Parameter 1 = number of pixels in strip
// Parameter 2 = Arduino pin number (most are valid)
// Parameter 3 = pixel type flags, add together as needed:
//   NEO_KHZ800  800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
//   NEO_KHZ400  400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
//   NEO_GRB     Pixels are wired for GRB bitstream (most NeoPixel products)
//   NEO_RGB     Pixels are wired for RGB bitstream (v1 FLORA pixels, not v2)
//   NEO_RGBW    Pixels are wired for RGBW bitstream (NeoPixel RGBW products)
Adafruit_NeoPixel strip = Adafruit_NeoPixel(12, PIN, NEO_GRB + NEO_KHZ800);

// IMPORTANT: To reduce NeoPixel burnout risk, add 1000 uF capacitor across
// pixel power leads, add 300 - 500 Ohm resistor on first pixel's data input
// and minimize distance between Arduino and first pixel.  Avoid connecting
// on a live circuit...if you must, connect GND first.

void setup() {
  // This is for Trinket 5V 16MHz, you can remove these three lines if you are not using a Trinket
  #if defined (__AVR_ATtiny85__)
    if (F_CPU == 16000000) clock_prescale_set(clock_div_1);
  #endif
  // End of trinket special code


  strip.begin();
  strip.show(); // Initialize all pixels to 'off'
}

void loop() {
  // Some example procedures showing how to display to the pixels:
  colorWipe(strip.Color(255, 0, 0), 50); // Red
  colorWipe(strip.Color(0, 255, 0), 50); // Green
  colorWipe(strip.Color(0, 0, 255), 50); // Blue
//colorWipe(strip.Color(0, 0, 0, 255), 50); // White RGBW
  // Send a theater pixel chase in...
  theaterChase(strip.Color(127, 127, 127), 50); // White
  theaterChase(strip.Color(127, 0, 0), 50); // Red
  theaterChase(strip.Color(0, 0, 127), 50); // Blue

  rainbow(20);
  rainbowCycle(20);
  theaterChaseRainbow(50);
}

// Fill the dots one after the other with a color
void colorWipe(uint32_t c, uint8_t wait) {
  for(uint16_t i=0; i<strip.numPixels(); i++) {
    strip.setPixelColor(i, c);
    strip.show();
    delay(wait);
  }
}

void rainbow(uint8_t wait) {
  uint16_t i, j;

  for(j=0; j<256; j++) {
    for(i=0; i<strip.numPixels(); i++) {
      strip.setPixelColor(i, Wheel((i+j) & 255));
    }
    strip.show();
    delay(wait);
  }
}

// Slightly different, this makes the rainbow equally distributed throughout
void rainbowCycle(uint8_t wait) {
  uint16_t i, j;

  for(j=0; j<256*5; j++) { // 5 cycles of all colors on wheel
    for(i=0; i< strip.numPixels(); i++) {
      strip.setPixelColor(i, Wheel(((i * 256 / strip.numPixels()) + j) & 255));
    }
    strip.show();
    delay(wait);
  }
}

//Theatre-style crawling lights.
void theaterChase(uint32_t c, uint8_t wait) {
  for (int j=0; j<10; j++) {  //do 10 cycles of chasing
    for (int q=0; q < 3; q++) {
      for (uint16_t i=0; i < strip.numPixels(); i=i+3) {
        strip.setPixelColor(i+q, c);    //turn every third pixel on
      }
      strip.show();

      delay(wait);

      for (uint16_t i=0; i < strip.numPixels(); i=i+3) {
        strip.setPixelColor(i+q, 0);        //turn every third pixel off
      }
    }
  }
}

//Theatre-style crawling lights with rainbow effect
void theaterChaseRainbow(uint8_t wait) {
  for (int j=0; j < 256; j++) {     // cycle all 256 colors in the wheel
    for (int q=0; q < 3; q++) {
      for (uint16_t i=0; i < strip.numPixels(); i=i+3) {
        strip.setPixelColor(i+q, Wheel( (i+j) % 255));    //turn every third pixel on
      }
      strip.show();

      delay(wait);

      for (uint16_t i=0; i < strip.numPixels(); i=i+3) {
        strip.setPixelColor(i+q, 0);        //turn every third pixel off
      }
    }
  }
}

// Input a value 0 to 255 to get a color value.
// The colours are a transition r - g - b - back to r.
uint32_t Wheel(byte WheelPos) {
  WheelPos = 255 - WheelPos;
  if(WheelPos < 85) {
    return strip.Color(255 - WheelPos * 3, 0, WheelPos * 3);
  }
  if(WheelPos < 170) {
    WheelPos -= 85;
    return strip.Color(0, WheelPos * 3, 255 - WheelPos * 3);
  }
  WheelPos -= 170;
  return strip.Color(WheelPos * 3, 255 - WheelPos * 3, 0);
}

Comments

Similar projects you might like

Stereo NeoPixel Ring VU Meter

Project showcase by ericBcreator

  • 29,185 views
  • 268 comments
  • 70 respects

Simple wall clock using Adafruit 1/4 60 Ring Neopixel

Project tutorial by antiElectron

  • 6,692 views
  • 0 comments
  • 34 respects

Notification IoT Using NeoPixel and Smartphone

Project showcase by Team Geny Studio

  • 4,404 views
  • 1 comment
  • 6 respects

A Model Lighthouse Using an Adafruit NeoPixel Ring

Project tutorial by Jeremy Lindsay

  • 1,109 views
  • 2 comments
  • 8 respects

NeoPixel LEDs: Arduino Basics

by Alex Glow

  • 43,196 views
  • 1 comment
  • 46 respects

Arduino Clock with Neopixel Ring Animation

Project tutorial by Alexander

  • 42,073 views
  • 39 comments
  • 64 respects
Add projectSign up / Login