Li.Po. Battery charger with BT Telemetry

For 2s1p (7.4V) battery packs, it does balancing, ready for a load circuit.

Mar 21, 2022

•

8185 views

•

0 respects

embedded

greener planet

robots

Components and supplies

Arduino Nano R3

Project description

Code

BTMonitor for Android (.apk)

batchfile

Copy the file on your mobile phone or tablet and install it

1inary file (no preview

inary file (no preview

BTMonitor source code (.aia)

batchfile

To edit the .aia file import it at ai2.appinventor.mit.edu website

1inary file (no preview

inary file (no preview

BTMonitor source code (.aia)

batchfile

To edit the .aia file import it at ai2.appinventor.mit.edu website

1inary file (no preview

inary file (no preview

BTMonitor for Android (.apk)

batchfile

Copy the file on your mobile phone or tablet and install it

1inary file (no preview

inary file (no preview

Arduino .INO Charger sketch

arduino

1/*
2  CHARGER for 2S Lipo battery
3  by Marco Zonca, 2022
4  
5  This sketch works as 2S LiPo Charger, originally made for Autopilot2 for small  sailing boats
6  Arduino Nano as MCU, 3 relais, LM317, ua7812, 3 Thermistors TMP36,  DAC module, 2 fuses, 4 BC337 NPN, 5W ceramic resistor, 2 RGB LED,
7  resistors  and capacitors, Buzzer, JST connectors, Cooling Fan, Bluetooth HC-05, etc.;
8
9/*  
10  WARNING: before switching Relais2 ON or OFF,
11  switch OFF Relais1 first,  then Relais2, then Relais1 ON again if necessary;
12  This circuit KEEPS SEPARATED  the battery ground from any other ground because during balanced charging
13  the  pins Cells, (-) and (+), are necessarily switched from one CELL to another, and  inverted polarity at common wire!
14 
15  LETS CONNECT the load only by the way  of X1-LOAD connector; the X1-LOAD power is automatically full disconnected when  charging (both wires (-) and (+))
16   
17*/
18
19#include <Wire.h>
20#include  <Adafruit_MCP4725.h>
21
22Adafruit_MCP4725 DAC;
23
24//--------------------------------------------------Charging  constant Values
25const float CBatt = 2.600;  // put here the battery power A/h
26const  float VCmin = 3.20;  // absolute minimum cell Voltage
27const float VCMax = 4.22;  // absolute max cell voltage
28const float VCfinalize = 4.18;  // finalize charging  cell voltage (after this it will charge at fixed voltage and limited current)
29const  float VCchgd = 4.18;  // already charged cell voltage (skip charging)
30const float  ETAdd = 60;  // additionally time in minutes for charging (finalize)
31const float  ETFact = 1.20;  // coefficent estimated charging time (plus additionally ETAdd)
32const  float ETFactAlarm = 2.00;  // coefficent estimated charging time sets Alarm too  (plus additionally ETAdd)
33const float CellChgCurrent = CBatt/5; // charging current  1/5 of battery (cell) A/h i.e. 2.600 / 5 = 0.520 A
34const float CellFinalizeCurrent  = CellChgCurrent / 100 * 20; // % of charging current in finalizing mode, if below  then stop charging (see VCfinalize)
35const float CellSlowDownCurrent = CellChgCurrent  / 100 * 50; // % of charging current in slow down mode (LM317 or uA7812 or Battery  high temperature)
36const float VPower = 5.0;  // max DAC voltage
37const byte  HighTRegH = 60; // LM317 or uA7812 high (threshold H) temperature C
38const byte  HighTRegL = 50; // LM317 or uA7812 high (threshold L) temperature C
39const byte  HighTBatH = 40; // battery high (threshold H) temperature C
40const byte HighTBatL  = 30; // battery high (threshold L) temperature C
41const byte FanTRHigh = 55;  // Fan (threshold H) LM317 or uA7812 temperature C
42const byte FanTRLow = 45;  // Fan (threshold L) LM317 or uA7812 temperature C
43const byte FanTBHigh = 36;  // Fan (threshold H) battery temperature C
44const byte FanTBLow = 32;  // Fan  (threshold L) battery temperature C
45const byte RegulatorTAlarm = 70;  // regulators  TC alarm (STOP charging)
46const byte BatteryTAlarm = 45;  // battery TC alarm  (STOP charging)
47//--------------------------------------------------Charging  constant Values
48
49const byte Relais1ConnectCellsPin = 2; 
50const byte Relais2SwitchCellsPin  = 3;
51const byte RGBledBluePin[3] = {0,4,6};
52const byte RGBledRedPin[3] = {0,5,7};
53const  byte FanPWMPin = 9;
54const byte VcellPin = 14;
55const byte VoutPin = 15;
56const  byte BuzzerPin = 16;
57const byte TMP36_BatteryPin = 17;
58const byte TMP36_7812Pin  = 20;
59const byte TMP36_317Pin = 21;
60const byte Set_OFF = LOW;
61const byte  Set_ON = HIGH;
62const int PrintDebugInterval = 4000;
63const int CheckChargeInterval  = 10000;
64const byte DAC_Address = 0x60;
65const float DAC_InitialV = 3.0;  //  charger Volt to cell (it is an initial/parking value, should not charge at this  value!)
66const boolean IsDEBUG = true;  // set this as TRUE for Serial Monitor  debug data output
67const float Rload = 0.47;  // shunt resistor
68
69boolean  IsCharging = false;
70boolean IsOverTime = false;
71boolean IsAlreadyCharged =  false;
72boolean IsSlowDown = false;
73boolean IsALARM = false;
74
75byte PhaseNr  = 0;
76byte WhichCellIsOn = 0;
77byte WhichFanSpeedIsOn = 0;
78int FanSpeed[3]  = {255*0/100, 255*90/100, 255*100/100};  // % of max speed, 0% normal TC, 90% high  TC, 100% ALARM
79
80float TempBattery = 0;
81float Temp7812 = 0;
82float Temp317  = 0;
83float Vcell = 0;
84float Voutput = 0;
85float Vload = 0;
86float Aload  = 0;
87float SetVOutput = 0;
88float SetDAC = 0;
89float TFull = 0;  // estimated  charge time in minutes
90float TRemain[3] = {0,0,0};  //  estimated remaining time  of charging in minutes
91float TScale = 0;  // time ETAdd reduction factor 
92float  C_OverTime[3] = {0,0,0};  // estimated time of charging in minutes
93float C_AlarmTime[3]  = {0,0,0};  // estimated time of charging in minutes sets Alarm
94float SoC[3]  = {0,0,0}; // state of charge in %
95float VInitCell[3] = {0,0,0};  // initial  charging cell voltage
96float VFinalCell[3] = {0,0,0};  // final charging cell  voltage
97
98unsigned long lastPrintDebugMillis = 0;
99unsigned long lastCheckChargeMillis  = 0;
100unsigned long ChTimeStart[3] = {0,0,0};  // charging start time, time elapsed  as minutes from power-up
101unsigned long ChTimeEnd[3] = {0,0,0};  // charging start  time, time elapsed as minutes from power-up
102unsigned long ChTimeNow = 0;  //  now time, time elapsed as minutes from power-up
103
104void setup() {
105  if (IsDEBUG)  Serial.begin(38400);  // output both serial monitor & bluetooth HC-05
106  DAC.begin(DAC_Address);
107  pinMode(RGBledBluePin[1], OUTPUT);
108  pinMode(RGBledRedPin[1], OUTPUT);
109  pinMode(RGBledBluePin[2], OUTPUT);
110  pinMode(RGBledRedPin[2], OUTPUT);
111  pinMode(TMP36_BatteryPin, INPUT);
112  pinMode(TMP36_7812Pin, INPUT);
113  pinMode(TMP36_317Pin,  INPUT);
114  pinMode(VcellPin, INPUT);
115  pinMode(VoutPin, INPUT);
116  pinMode(Relais1ConnectCellsPin,OUTPUT);
117  pinMode(Relais2SwitchCellsPin,OUTPUT);
118  pinMode(BuzzerPin,OUTPUT);
119  pinMode(FanPWMPin,OUTPUT);
120  DisconnectAllCells();
121  WriteDACVOutput(DAC_InitialV);
122  buzzerBips(1);
123  ledShow();
124}//setup()
125
126void loop() {
127  readTemperatures();
128  readVAvalues();
129  if ((IsDEBUG) && (lastPrintDebugMillis + PrintDebugInterval) < millis()) serialPrintDebug();
130  if (IsALARM==false) {
131    if ((lastCheckChargeMillis + CheckChargeInterval)  < millis()) checkCharge();
132    if (WhichCellIsOn) display();
133   } else {  //  ALARM
134      if (WhichCellIsOn) DisconnectAllCells();
135      display();
136      buzzerBips(5);
137  }//IsALARM
138}//loop()
139
140void checkCharge() {  //  -----------------------------------------------------------------------------------  start, charge or skip, finish
141  float ri = 0;
142  float current = 0;
143  float  c = 0;
144  TFull = roundZeroDec(CBatt / CellChgCurrent) * 60;
145  current=CellChgCurrent;
146  if (IsSlowDown == true) {  // limiting current during high TC
147    TFull = roundZeroDec(CBatt  / CellSlowDownCurrent) * 60;
148    current=CellSlowDownCurrent;
149  }
150  if  (Vcell > VCfinalize) {
151    TFull = roundZeroDec(CBatt / CellFinalizeCurrent)  * 60;
152    TScale=(((Aload - CellFinalizeCurrent) * 100) / (current - CellFinalizeCurrent))  / 100;
153   } else {
154    TScale=1;
155  }
156  
157  if (IsCharging == true)  { // ----------------------------------------------------- charging
158    if (Vcell  > VCMax) {  // ======== stop charging, over VCMax...
159      ChTimeEnd[WhichCellIsOn]=roundZeroDec(((millis()/1000)/60)+1);
160      VFinalCell[WhichCellIsOn]=Vcell;  // final cell voltage
161      DisconnectAllCells();
162      WriteDACVOutput(DAC_InitialV);
163      IsCharging=false;
164      if (PhaseNr==1)  buzzerBips(2);
165      if (PhaseNr==2) buzzerBips(3);
166      if (IsDEBUG) Serial.println("STOP,  over VCMax...");
167     } else {
168      if (Vcell <= VCfinalize) {  // ==========  tuning, fixed current
169        for (ri=(SetVOutput - 0.06);ri=ri+0.02;ri<VPower)  {  // increment DAC voltage till reaching "current"
170          WriteDACVOutput(ri);
171          readVAvalues();
172          if (IsDEBUG) serialPrintChg("TUNE");
173          if ((Aload >= current) || (Vcell>=(VCMax - 0.02))) break;
174        }
175      }//IfVcell<=Finalize
176      if (Vcell > VCfinalize) {  // ============ finalize,  fixed voltage and limited current
177        for ((ri=SetVOutput - 0.03);ri=ri+0.01;ri<=VCMax)  {  // increment DAC voltage till reaching "VCMax-0.02"
178          WriteDACVOutput(ri);
179          readVAvalues();
180          if (IsDEBUG) serialPrintChg("FINAL");
181          if ((Aload >= current) || (Vcell>=(VCMax - 0.02))) break;
182        }
183        if (Aload < CellFinalizeCurrent) {  // === stop charging, below finalizing  current, perfect
184          ChTimeEnd[WhichCellIsOn]=roundZeroDec(((millis()/1000)/60)+1);
185          VFinalCell[WhichCellIsOn]=Vcell;  // final cell voltage
186          DisconnectAllCells();
187          WriteDACVOutput(DAC_InitialV);
188          IsCharging=false;
189          if  (PhaseNr==1) buzzerBips(2);
190          if (PhaseNr==2) buzzerBips(3);
191          if  (IsDEBUG) Serial.println("END, current finalized");
192        }
193      }//IfVcell>=Finalize
194    }//ifVCell>=VCMax
195  }//IfIsCharging==true
196  
197  if (IsCharging == false)  {  // ----------------------------------------------------- phase and start
198    if (PhaseNr < 2) {  // =============== switch Cell -> 1 -> 2 
199      PhaseNr++;
200      ConnectCell_N(PhaseNr);
201      readVAvalues();
202      if (Vcell >= VCchgd)  {
203        IsAlreadyCharged=true;
204       } else {
205        IsAlreadyCharged=false;
206      }
207      IsOverTime=false;
208      if (IsAlreadyCharged == false) {  //  ================ start charging, fixed current
209        ChTimeStart[WhichCellIsOn]=roundZeroDec(((millis()/1000)/60)+1);
210        VInitCell[WhichCellIsOn]=Vcell;  // initial cell voltage
211        C_OverTime[WhichCellIsOn]  = roundZeroDec(((((CBatt / CellChgCurrent) * 60) * (VCMax - 0.02 - VInitCell[WhichCellIsOn]))  * ETFact) + ETAdd); // estimated maximum time of charging
212        C_AlarmTime[WhichCellIsOn]  = roundZeroDec(((((CBatt / CellChgCurrent) * 60) * (VCMax - 0.02 - VInitCell[WhichCellIsOn]))  * ETFactAlarm) + ETAdd); // estimated maximum time of charging then setes Alarm
213        for (ri=Vcell;ri=ri+0.02;ri<VPower) {  // increment DAC voltage till reaching  "current"
214          WriteDACVOutput(ri);
215          readVAvalues();
216          if  (IsDEBUG) serialPrintChg("START");
217          if ((Aload >= current) || (Vcell>=(VCMax-0.02)))  break;
218        }
219        IsCharging=true;
220       } else {
221        ChTimeStart[WhichCellIsOn]=roundZeroDec(((millis()/1000)/60)+1);  // ======== charging not necessary, already charged...
222        VInitCell[WhichCellIsOn]=Vcell;  // initial cell voltage
223        C_OverTime[WhichCellIsOn] = roundZeroDec(((((CBatt  / CellChgCurrent) * 60) * (VCMax - 0.02 - VInitCell[WhichCellIsOn])) * ETFact) +  ETAdd); // estimated maximum time of charging
224        C_AlarmTime[WhichCellIsOn]  = roundZeroDec(((((CBatt / CellChgCurrent) * 60) * (VCMax - 0.02 - VInitCell[WhichCellIsOn]))  * ETFactAlarm) + ETAdd); // estimated maximum time of charging then sets Alarm
225        ChTimeEnd[WhichCellIsOn]=roundZeroDec(((millis()/1000)/60)+1);
226        VFinalCell[WhichCellIsOn]=Vcell;  // final cell voltage
227        display();
228        DisconnectAllCells();
229        WriteDACVOutput(DAC_InitialV);
230        if (PhaseNr==1) buzzerBips(2);
231        if (PhaseNr==2) buzzerBips(3);
232        if (IsDEBUG) Serial.println("END,  already charged");
233      }//IsAlreadyCharged==false
234    }//IfPhase<2
235  }//IsCharging==false
236
237  if (WhichCellIsOn) {
238    SoC[WhichCellIsOn] =  roundZeroDec(100 - ((VCMax - 0.02 - Vcell) * 100)); // state of charge in %
239    ChTimeNow=roundZeroDec(((millis()/1000)/60)+1);  // now time as minutes from  power-up +1
240    if ((ChTimeNow-ChTimeStart[WhichCellIsOn]) > C_OverTime[WhichCellIsOn])  IsOverTime=true;
241    if ((ChTimeNow-ChTimeStart[WhichCellIsOn]) > C_AlarmTime[WhichCellIsOn])  IsALARM=true;
242    TRemain[WhichCellIsOn] = roundZeroDec(((TFull * (VCMax - 0.02  - Vcell)) * ETFact) + (ETAdd * TScale));  //  estimated remaining time of charging  in minutes
243  }
244  lastCheckChargeMillis=millis();
245}//checkCharge()
246
247void  buzzerBips(byte n) {
248  byte q=0;
249  for (q=1;q<=n;q++) {
250    digitalWrite(BuzzerPin,  HIGH);
251    delay(100);  
252    digitalWrite(BuzzerPin, LOW);
253    delay(100);  
254  }
255}//buzzerBips()
256
257/*  
258  WARNING: before switching Relais2  ON or OFF,
259  switch OFF Relais1 first, then Relais2, then Relais1 ON again if  necessary;
260  This circuit KEEPS SEPARATED the battery ground from any other ground  because during balanced charging
261  the pins Cells, (-) and (+), are necessarely  switched from one CELL to another, and inverted polarity at common wire!
262*/
263void  DisconnectAllCells() {  // ------------------------------ disconnect Cells by Relais
264  digitalWrite(Relais1ConnectCellsPin, Set_OFF);
265  delay(1000);
266  digitalWrite(Relais2SwitchCellsPin,  Set_OFF);
267  delay(1000);
268  WhichCellIsOn = 0;
269}//DisconnectAllCells()
270
271void  ConnectCell_N(byte c) {  // ----------------------------- connect Cell by Relais
272  switch (c) {
273    case 1:
274      digitalWrite(Relais1ConnectCellsPin, Set_OFF);
275      delay(1000);
276      digitalWrite(Relais2SwitchCellsPin, Set_OFF);
277      delay(1000);
278      digitalWrite(Relais1ConnectCellsPin, Set_ON);
279      delay(1000);
280    break;
281    case 2:
282      digitalWrite(Relais1ConnectCellsPin, Set_OFF);
283      delay(1000);
284      digitalWrite(Relais2SwitchCellsPin, Set_ON);
285      delay(1000);
286      digitalWrite(Relais1ConnectCellsPin,  Set_ON);
287      delay(1000);
288    break;
289  }
290  WhichCellIsOn = c;
291}//ConnectCell_N()
292
293void  WriteDACVOutput(float v) {  // ------------------------- write DAC
294  SetVOutput  = v;
295  SetDAC = ((SetVOutput - 1.25 + 0.75) * (4095.0 / 5.0));  // (Vdac - VdacADD  + Vdiod) * (Res / Vref)
296  DAC.setVoltage(SetDAC, false);
297  delay(1000);
298}//WriteDACVOutput()
299
300void  display() {  // ---------------------------------------- display LED status
301  digitalWrite(RGBledBluePin[WhichCellIsOn],LOW);
302  digitalWrite(RGBledRedPin[WhichCellIsOn],LOW);
303  if (IsALARM==true) {
304    blink_redALARM();
305  } else {
306    if (IsAlreadyCharged==false)  {
307      if ((IsCharging==true)) {
308        if (IsOverTime==false) {
309          if  (SoC[WhichCellIsOn] <= 20) blink_red();
310          if (SoC[WhichCellIsOn] > 20  && SoC[WhichCellIsOn] <=40) blink_red_purple();
311          if (SoC[WhichCellIsOn]  > 40 && SoC[WhichCellIsOn] <=60) blink_purple();
312          if (SoC[WhichCellIsOn]  > 60 && SoC[WhichCellIsOn] <=80) blink_purple_blue();
313          if (SoC[WhichCellIsOn]  > 80 && SoC[WhichCellIsOn] <=90) blink_blue();
314          if (SoC[WhichCellIsOn]  > 90) blink_slowblue();
315         } else {
316          blink_quickblue();  //overtime  warning
317        }//over
318       } else {
319        steady_red();  //deciding  what to do
320      }//charging
321     } else {
322      steady_blue();  //charged  
323    }//already
324  }//IsALARM
325}//display()
326
327void readVAvalues() {  // ---------------------------------- read V, A, values
328  float n=0;
329  float  s=0;
330  float VCmem=0;
331  float VOmem=0;
332  int x=0;
333  for (x=1;x<=100;x++)  {  // x nr. of readings as average filter
334    n = analogRead(VcellPin);
335    s  = ((5.0 * n) / 1023);  // from cell
336    VCmem=VCmem+s;
337    n = analogRead(VoutPin);
338    s = ((5.0 * n) / 1023);  // from LM317
339    VOmem=VOmem+s;
340  }
341  s=(VCmem/(x-1));
342  Vcell = (s + ((s * 1.40) /100));  // +- % arbitrary correction (not active if  = 0.00)
343  Vcell = roundThreeDec(Vcell);
344  s=(VOmem/(x-1));
345  Voutput =  (s + ((s * 1.40) /100));  // +- % arbitrary correction (not active if = 0.00)
346  Voutput = roundThreeDec(Voutput);
347  s=(Voutput-Vcell);
348  Vload = roundThreeDec(s);
349  n=(Vload/Rload);
350  Aload = roundThreeDec(n);
351}//readVAvalues()
352
353void  readTemperatures() {  // --------------------------------- read temperatures
354  int n=0;
355  n = analogRead(TMP36_BatteryPin);
356  TempBattery = (((5.0 * n)  / 1023) - 0.500 ) * 100;  // (-500mV=offset) 0 to 500 = below zero values
357  TempBattery  = roundZeroDec(TempBattery);
358  n = analogRead(TMP36_7812Pin);
359  Temp7812 =  (((5.0 * n) / 1023) - 0.500 ) * 100;
360  Temp7812 = roundZeroDec(Temp7812);
361  n = analogRead(TMP36_317Pin);
362  Temp317 = (((5.0 * n) / 1023) - 0.500 ) * 100;
363  Temp317 = roundZeroDec(Temp317);
364  if ((Temp7812 < HighTRegL) && (Temp317 <  HighTRegL) && (TempBattery < HighTBatL)) {  // current
365    IsSlowDown = false;  // will normal chg current
366  }
367  if ((Temp7812 > HighTRegH) || (Temp317  > HighTRegH) || (TempBattery > HighTBatH)) {
368    IsSlowDown = true;  // will  decrease chg current
369  }
370  if (IsALARM==false) {
371    if ((Temp7812 < FanTRLow)  && (Temp317 < FanTRLow) && (TempBattery < FanTBLow)) {  // fan
372      analogWrite(FanPWMPin,  FanSpeed[0]);  // Fan normal temperatures
373      WhichFanSpeedIsOn=FanSpeed[0];
374    }
375    if ((Temp7812 > FanTRHigh) || (Temp317 > FanTRHigh) || (TempBattery  > FanTBHigh)) {
376      analogWrite(FanPWMPin, FanSpeed[1]);  // Fan high temperatures
377      WhichFanSpeedIsOn=FanSpeed[1];
378    }
379    if ((Temp7812 > RegulatorTAlarm)  || (Temp317 > RegulatorTAlarm) || (TempBattery > BatteryTAlarm)) {  // ALARM
380      IsALARM = true;  // will STOP charging etc.
381      analogWrite(FanPWMPin,  FanSpeed[2]);  // Fan ALARM temperatures
382      WhichFanSpeedIsOn=FanSpeed[2];
383    }
384   } else {
385    analogWrite(FanPWMPin, FanSpeed[2]);  // Fan ALARM
386    WhichFanSpeedIsOn=FanSpeed[2];    
387  }
388}//readTemperatures()
389
390void  blink_red() {  // ----------------------------------------- led
391  delay(500);
392  digitalWrite(RGBledRedPin[WhichCellIsOn], HIGH);
393}
394void blink_redALARM()  {
395  digitalWrite(RGBledRedPin[1], LOW);
396  digitalWrite(RGBledRedPin[2], LOW);
397  digitalWrite(RGBledBluePin[1], LOW);
398  digitalWrite(RGBledBluePin[2], LOW);
399  delay(100);
400  digitalWrite(RGBledRedPin[1], HIGH);
401  delay(100);
402  digitalWrite(RGBledRedPin[1],  LOW);
403  digitalWrite(RGBledRedPin[2], HIGH);
404  delay(100);
405}
406void blink_blue()  {
407  delay(500);
408  digitalWrite(RGBledBluePin[WhichCellIsOn], HIGH);
409  delay(500);
410}
411void  blink_purple() {
412  delay(500);
413  digitalWrite(RGBledRedPin[WhichCellIsOn],  HIGH);
414  digitalWrite(RGBledBluePin[WhichCellIsOn], HIGH);
415  delay(500);
416}
417void  blink_red_purple() {
418  delay(500);
419  digitalWrite(RGBledRedPin[WhichCellIsOn],  HIGH);
420  delay(1000);
421  digitalWrite(RGBledBluePin[WhichCellIsOn], HIGH);
422  delay(500);
423}
424void blink_purple_blue() {
425  delay(500);
426  digitalWrite(RGBledRedPin[WhichCellIsOn],  HIGH);
427  digitalWrite(RGBledBluePin[WhichCellIsOn], HIGH);
428  delay(1000);
429  digitalWrite(RGBledRedPin[WhichCellIsOn], LOW);
430  digitalWrite(RGBledBluePin[WhichCellIsOn],  HIGH);
431  delay(500);
432}
433void blink_slowblue() {
434  delay(1000);
435  digitalWrite(RGBledBluePin[WhichCellIsOn],  HIGH);
436  delay(2000);
437}
438void blink_quickblue() {
439  delay(100);
440  digitalWrite(RGBledBluePin[WhichCellIsOn],  HIGH);
441  delay(100);
442}
443void steady_blue() {
444  digitalWrite(RGBledBluePin[WhichCellIsOn],  HIGH);
445}
446void steady_red() {
447  digitalWrite(RGBledRedPin[WhichCellIsOn],  HIGH);
448}
449
450void ledShow() {  // --------------------------------------------  initial show & Fan
451  digitalWrite(RGBledBluePin[1], HIGH);
452  digitalWrite(RGBledRedPin[1],  LOW);
453  digitalWrite(RGBledBluePin[2], LOW);
454  digitalWrite(RGBledRedPin[2],  LOW);
455  delay(500);
456  digitalWrite(RGBledBluePin[1], HIGH);
457  digitalWrite(RGBledRedPin[1],  HIGH);
458  digitalWrite(RGBledBluePin[2], LOW);
459  digitalWrite(RGBledRedPin[2],  LOW);
460  delay(500);
461  digitalWrite(RGBledBluePin[1], LOW);
462  digitalWrite(RGBledRedPin[1],  HIGH);
463  digitalWrite(RGBledBluePin[2], LOW);
464  digitalWrite(RGBledRedPin[2],  LOW);
465  delay(500);
466  digitalWrite(RGBledBluePin[1], LOW);
467  digitalWrite(RGBledRedPin[1],  LOW);
468  digitalWrite(RGBledBluePin[2], HIGH);
469  digitalWrite(RGBledRedPin[2],  LOW);
470  delay(500);
471  digitalWrite(RGBledBluePin[1], LOW);
472  digitalWrite(RGBledRedPin[1],  LOW);
473  digitalWrite(RGBledBluePin[2], HIGH);
474  digitalWrite(RGBledRedPin[2],  HIGH);
475  delay(500);
476  digitalWrite(RGBledBluePin[1], LOW);
477  digitalWrite(RGBledRedPin[1],  LOW);
478  digitalWrite(RGBledBluePin[2], LOW);
479  digitalWrite(RGBledRedPin[2],  HIGH);
480  delay(500);
481  digitalWrite(RGBledBluePin[1], LOW);
482  digitalWrite(RGBledRedPin[1],  HIGH);
483  digitalWrite(RGBledBluePin[2], LOW);
484  digitalWrite(RGBledRedPin[2],  HIGH);
485  analogWrite(FanPWMPin, FanSpeed[1]);  // Fan high temperatures test
486  delay(5000);
487  analogWrite(FanPWMPin, FanSpeed[0]);
488}//ledShow()
489
490void  serialPrintChg(const char msg[]) {  // -------------------------------- print charging
491  Serial.print(msg);
492  Serial.print(":");
493  Serial.print(" Cell=");
494  Serial.print(WhichCellIsOn);
495  Serial.print(" Vdac=");
496  Serial.print(SetVOutput,3);
497  Serial.print(" Vcel=");
498  Serial.print(Vcell,3);
499  Serial.print(" Acel=");
500  Serial.println(Aload,3);
501}
502
503void serialPrintDebug() {  // -----------------------------------------------  print debug serial & bluetooth
504  Serial.print("TBatt=");  // temperatures
505  Serial.print(TempBattery,0);
506  Serial.print(" T7812=");
507  Serial.print(Temp7812,0);
508  Serial.print(" T317=");
509  
510  Serial.print(Temp317,0);
511  Serial.print("  Fan=");
512  Serial.print(WhichFanSpeedIsOn);
513  Serial.println("/255");
514
515  Serial.print("Cell=");  // VA values
516  Serial.print(WhichCellIsOn);
517  Serial.print("  VCel=");
518  Serial.print(Vcell,3);
519  Serial.print(" Vdac=");
520  Serial.print(Voutput,3);
521  Serial.print(" ACel=");
522  Serial.println(Aload,3);
523
524  Serial.print("IsAlrdy=");  // status
525  Serial.print(IsAlreadyCharged);
526  Serial.print(" IsCharg=");
527  Serial.print(IsCharging);
528  Serial.print(" IsOver=");
529  Serial.print(IsOverTime);
530  Serial.print(" IsALRM=");
531  Serial.print(IsALARM);
532  Serial.print(" IsSlow=");
533  Serial.println(IsSlowDown);
534
535  Serial.print("Start[1]=");  // charging  times [1]
536  Serial.print(ChTimeStart[1]);
537  Serial.print(" End[1]=");
538  if (ChTimeEnd[1] > 0) {
539    Serial.print(ChTimeEnd[1]);
540  } else {
541    Serial.print("?");
542  }
543  Serial.print(" Time[1]=");
544  if (ChTimeEnd[1] > 0) {
545    Serial.print(long(ChTimeEnd[1]  - ChTimeStart[1]));
546  } else {
547    Serial.print("?");
548  }
549  Serial.print("  VInit[1]=");
550  Serial.print(VInitCell[1],3);
551  Serial.print(" VFinal[1]=");
552  Serial.print(VFinalCell[1],3);
553  Serial.print(" Over[1]=");
554  Serial.print(C_OverTime[1]);
555  Serial.print(" Alarm[1]=");
556  Serial.print(C_AlarmTime[1]);
557  Serial.print("  Remain[1]=");
558  Serial.print(TRemain[1]);
559  Serial.print(" SoC%[1]=");
560  Serial.println(SoC[1]);
561
562  Serial.print("Start[2]=");  // charging times  [2]
563  Serial.print(ChTimeStart[2]);
564  Serial.print(" End[2]=");
565  if  (ChTimeEnd[2] > 0) {
566    Serial.print(ChTimeEnd[2]);
567  } else {
568    Serial.print("?");
569  }
570  Serial.print(" Time[2]=");
571  if (ChTimeEnd[2] > 0) {
572    Serial.print(long(ChTimeEnd[2]  - ChTimeStart[2]));
573  } else {
574    Serial.print("?");
575  }
576  Serial.print("  VInit[2]=");
577  Serial.print(VInitCell[2],3);
578  Serial.print(" VFinal[2]=");
579  Serial.print(VFinalCell[2],3);
580  Serial.print(" Over[2]=");
581  Serial.print(C_OverTime[2]);
582  Serial.print(" Alarm[2]=");
583  Serial.print(C_AlarmTime[2]);
584  Serial.print("  Remain[2]=");
585  Serial.print(TRemain[2]);
586  Serial.print(" SoC%[2]=");
587  Serial.println(SoC[2]);
588  
589  Serial.print("TimeNow=");
590  Serial.println(ChTimeNow);
591
592  lastPrintDebugMillis=millis();
593}//serialPrintDebug()
594
595// round zero decimal  // ----------------------------------------------- rounds
596float roundZeroDec(float  f) {
597  float y, d;
598  y = f*1;
599  d = y - (int)y;
600  y = (float)(int)(f*1)/1;
601  if (d >= 0.5) {
602    y += 1;
603   } else {
604    if (d < -0.5) {
605      y  -= 1;
606    }
607  }
608  return y;
609}
610// round three decimals
611float roundThreeDec(float  f) {
612  float y, d;
613  y = f*1000;
614  d = y - (int)y;
615  y = (float)(int)(f*1000)/1000;
616  if (d >= 0.5) {
617    y += 0.001;
618   } else {
619    if (d < -0.5) {
620      y  -= 0.001;
621    }
622  }
623  return y;
624}
625

/*
  CHARGER for 2S Lipo battery
  by Marco Zonca, 2022
  
  This sketch works as 2S LiPo Charger, originally made for Autopilot2 for small  sailing boats
  Arduino Nano as MCU, 3 relais, LM317, ua7812, 3 Thermistors TMP36,  DAC module, 2 fuses, 4 BC337 NPN, 5W ceramic resistor, 2 RGB LED,
  resistors  and capacitors, Buzzer, JST connectors, Cooling Fan, Bluetooth HC-05, etc.;

/*  
  WARNING: before switching Relais2 ON or OFF,
  switch OFF Relais1 first,  then Relais2, then Relais1 ON again if necessary;
  This circuit KEEPS SEPARATED  the battery ground from any other ground because during balanced charging
  the  pins Cells, (-) and (+), are necessarily switched from one CELL to another, and  inverted polarity at common wire!
 
  LETS CONNECT the load only by the way  of X1-LOAD connector; the X1-LOAD power is automatically full disconnected when  charging (both wires (-) and (+))
   
*/

#include <Wire.h>
#include  <Adafruit_MCP4725.h>

Adafruit_MCP4725 DAC;

//--------------------------------------------------Charging  constant Values
const float CBatt = 2.600;  // put here the battery power A/h
const  float VCmin = 3.20;  // absolute minimum cell Voltage
const float VCMax = 4.22;  // absolute max cell voltage
const float VCfinalize = 4.18;  // finalize charging  cell voltage (after this it will charge at fixed voltage and limited current)
const  float VCchgd = 4.18;  // already charged cell voltage (skip charging)
const float  ETAdd = 60;  // additionally time in minutes for charging (finalize)
const float  ETFact = 1.20;  // coefficent estimated charging time (plus additionally ETAdd)
const  float ETFactAlarm = 2.00;  // coefficent estimated charging time sets Alarm too  (plus additionally ETAdd)
const float CellChgCurrent = CBatt/5; // charging current  1/5 of battery (cell) A/h i.e. 2.600 / 5 = 0.520 A
const float CellFinalizeCurrent  = CellChgCurrent / 100 * 20; // % of charging current in finalizing mode, if below  then stop charging (see VCfinalize)
const float CellSlowDownCurrent = CellChgCurrent  / 100 * 50; // % of charging current in slow down mode (LM317 or uA7812 or Battery  high temperature)
const float VPower = 5.0;  // max DAC voltage
const byte  HighTRegH = 60; // LM317 or uA7812 high (threshold H) temperature C
const byte  HighTRegL = 50; // LM317 or uA7812 high (threshold L) temperature C
const byte  HighTBatH = 40; // battery high (threshold H) temperature C
const byte HighTBatL  = 30; // battery high (threshold L) temperature C
const byte FanTRHigh = 55;  // Fan (threshold H) LM317 or uA7812 temperature C
const byte FanTRLow = 45;  // Fan (threshold L) LM317 or uA7812 temperature C
const byte FanTBHigh = 36;  // Fan (threshold H) battery temperature C
const byte FanTBLow = 32;  // Fan  (threshold L) battery temperature C
const byte RegulatorTAlarm = 70;  // regulators  TC alarm (STOP charging)
const byte BatteryTAlarm = 45;  // battery TC alarm  (STOP charging)
//--------------------------------------------------Charging  constant Values

const byte Relais1ConnectCellsPin = 2; 
const byte Relais2SwitchCellsPin  = 3;
const byte RGBledBluePin[3] = {0,4,6};
const byte RGBledRedPin[3] = {0,5,7};
const  byte FanPWMPin = 9;
const byte VcellPin = 14;
const byte VoutPin = 15;
const  byte BuzzerPin = 16;
const byte TMP36_BatteryPin = 17;
const byte TMP36_7812Pin  = 20;
const byte TMP36_317Pin = 21;
const byte Set_OFF = LOW;
const byte  Set_ON = HIGH;
const int PrintDebugInterval = 4000;
const int CheckChargeInterval  = 10000;
const byte DAC_Address = 0x60;
const float DAC_InitialV = 3.0;  //  charger Volt to cell (it is an initial/parking value, should not charge at this  value!)
const boolean IsDEBUG = true;  // set this as TRUE for Serial Monitor  debug data output
const float Rload = 0.47;  // shunt resistor

boolean  IsCharging = false;
boolean IsOverTime = false;
boolean IsAlreadyCharged =  false;
boolean IsSlowDown = false;
boolean IsALARM = false;

byte PhaseNr  = 0;
byte WhichCellIsOn = 0;
byte WhichFanSpeedIsOn = 0;
int FanSpeed[3]  = {255*0/100, 255*90/100, 255*100/100};  // % of max speed, 0% normal TC, 90% high  TC, 100% ALARM

float TempBattery = 0;
float Temp7812 = 0;
float Temp317  = 0;
float Vcell = 0;
float Voutput = 0;
float Vload = 0;
float Aload  = 0;
float SetVOutput = 0;
float SetDAC = 0;
float TFull = 0;  // estimated  charge time in minutes
float TRemain[3] = {0,0,0};  //  estimated remaining time  of charging in minutes
float TScale = 0;  // time ETAdd reduction factor 
float  C_OverTime[3] = {0,0,0};  // estimated time of charging in minutes
float C_AlarmTime[3]  = {0,0,0};  // estimated time of charging in minutes sets Alarm
float SoC[3]  = {0,0,0}; // state of charge in %
float VInitCell[3] = {0,0,0};  // initial  charging cell voltage
float VFinalCell[3] = {0,0,0};  // final charging cell  voltage

unsigned long lastPrintDebugMillis = 0;
unsigned long lastCheckChargeMillis  = 0;
unsigned long ChTimeStart[3] = {0,0,0};  // charging start time, time elapsed  as minutes from power-up
unsigned long ChTimeEnd[3] = {0,0,0};  // charging start  time, time elapsed as minutes from power-up
unsigned long ChTimeNow = 0;  //  now time, time elapsed as minutes from power-up

void setup() {
  if (IsDEBUG)  Serial.begin(38400);  // output both serial monitor & bluetooth HC-05
  DAC.begin(DAC_Address);
  pinMode(RGBledBluePin[1], OUTPUT);
  pinMode(RGBledRedPin[1], OUTPUT);
  pinMode(RGBledBluePin[2], OUTPUT);
  pinMode(RGBledRedPin[2], OUTPUT);
  pinMode(TMP36_BatteryPin, INPUT);
  pinMode(TMP36_7812Pin, INPUT);
  pinMode(TMP36_317Pin,  INPUT);
  pinMode(VcellPin, INPUT);
  pinMode(VoutPin, INPUT);
  pinMode(Relais1ConnectCellsPin,OUTPUT);
  pinMode(Relais2SwitchCellsPin,OUTPUT);
  pinMode(BuzzerPin,OUTPUT);
  pinMode(FanPWMPin,OUTPUT);
  DisconnectAllCells();
  WriteDACVOutput(DAC_InitialV);
  buzzerBips(1);
  ledShow();
}//setup()

void loop() {
  readTemperatures();
  readVAvalues();
  if ((IsDEBUG) && (lastPrintDebugMillis + PrintDebugInterval) < millis()) serialPrintDebug();
  if (IsALARM==false) {
    if ((lastCheckChargeMillis + CheckChargeInterval)  < millis()) checkCharge();
    if (WhichCellIsOn) display();
   } else {  //  ALARM
      if (WhichCellIsOn) DisconnectAllCells();
      display();
      buzzerBips(5);
  }//IsALARM
}//loop()

void checkCharge() {  //  -----------------------------------------------------------------------------------  start, charge or skip, finish
  float ri = 0;
  float current = 0;
  float  c = 0;
  TFull = roundZeroDec(CBatt / CellChgCurrent) * 60;
  current=CellChgCurrent;
  if (IsSlowDown == true) {  // limiting current during high TC
    TFull = roundZeroDec(CBatt  / CellSlowDownCurrent) * 60;
    current=CellSlowDownCurrent;
  }
  if  (Vcell > VCfinalize) {
    TFull = roundZeroDec(CBatt / CellFinalizeCurrent)  * 60;
    TScale=(((Aload - CellFinalizeCurrent) * 100) / (current - CellFinalizeCurrent))  / 100;
   } else {
    TScale=1;
  }
  
  if (IsCharging == true)  { // ----------------------------------------------------- charging
    if (Vcell  > VCMax) {  // ======== stop charging, over VCMax...
      ChTimeEnd[WhichCellIsOn]=roundZeroDec(((millis()/1000)/60)+1);
      VFinalCell[WhichCellIsOn]=Vcell;  // final cell voltage
      DisconnectAllCells();
      WriteDACVOutput(DAC_InitialV);
      IsCharging=false;
      if (PhaseNr==1)  buzzerBips(2);
      if (PhaseNr==2) buzzerBips(3);
      if (IsDEBUG) Serial.println("STOP,  over VCMax...");
     } else {
      if (Vcell <= VCfinalize) {  // ==========  tuning, fixed current
        for (ri=(SetVOutput - 0.06);ri=ri+0.02;ri<VPower)  {  // increment DAC voltage till reaching "current"
          WriteDACVOutput(ri);
          readVAvalues();
          if (IsDEBUG) serialPrintChg("TUNE");
          if ((Aload >= current) || (Vcell>=(VCMax - 0.02))) break;
        }
      }//IfVcell<=Finalize
      if (Vcell > VCfinalize) {  // ============ finalize,  fixed voltage and limited current
        for ((ri=SetVOutput - 0.03);ri=ri+0.01;ri<=VCMax)  {  // increment DAC voltage till reaching "VCMax-0.02"
          WriteDACVOutput(ri);
          readVAvalues();
          if (IsDEBUG) serialPrintChg("FINAL");
          if ((Aload >= current) || (Vcell>=(VCMax - 0.02))) break;
        }
        if (Aload < CellFinalizeCurrent) {  // === stop charging, below finalizing  current, perfect
          ChTimeEnd[WhichCellIsOn]=roundZeroDec(((millis()/1000)/60)+1);
          VFinalCell[WhichCellIsOn]=Vcell;  // final cell voltage
          DisconnectAllCells();
          WriteDACVOutput(DAC_InitialV);
          IsCharging=false;
          if  (PhaseNr==1) buzzerBips(2);
          if (PhaseNr==2) buzzerBips(3);
          if  (IsDEBUG) Serial.println("END, current finalized");
        }
      }//IfVcell>=Finalize
    }//ifVCell>=VCMax
  }//IfIsCharging==true
  
  if (IsCharging == false)  {  // ----------------------------------------------------- phase and start
    if (PhaseNr < 2) {  // =============== switch Cell -> 1 -> 2 
      PhaseNr++;
      ConnectCell_N(PhaseNr);
      readVAvalues();
      if (Vcell >= VCchgd)  {
        IsAlreadyCharged=true;
       } else {
        IsAlreadyCharged=false;
      }
      IsOverTime=false;
      if (IsAlreadyCharged == false) {  //  ================ start charging, fixed current
        ChTimeStart[WhichCellIsOn]=roundZeroDec(((millis()/1000)/60)+1);
        VInitCell[WhichCellIsOn]=Vcell;  // initial cell voltage
        C_OverTime[WhichCellIsOn]  = roundZeroDec(((((CBatt / CellChgCurrent) * 60) * (VCMax - 0.02 - VInitCell[WhichCellIsOn]))  * ETFact) + ETAdd); // estimated maximum time of charging
        C_AlarmTime[WhichCellIsOn]  = roundZeroDec(((((CBatt / CellChgCurrent) * 60) * (VCMax - 0.02 - VInitCell[WhichCellIsOn]))  * ETFactAlarm) + ETAdd); // estimated maximum time of charging then setes Alarm
        for (ri=Vcell;ri=ri+0.02;ri<VPower) {  // increment DAC voltage till reaching  "current"
          WriteDACVOutput(ri);
          readVAvalues();
          if  (IsDEBUG) serialPrintChg("START");
          if ((Aload >= current) || (Vcell>=(VCMax-0.02)))  break;
        }
        IsCharging=true;
       } else {
        ChTimeStart[WhichCellIsOn]=roundZeroDec(((millis()/1000)/60)+1);  // ======== charging not necessary, already charged...
        VInitCell[WhichCellIsOn]=Vcell;  // initial cell voltage
        C_OverTime[WhichCellIsOn] = roundZeroDec(((((CBatt  / CellChgCurrent) * 60) * (VCMax - 0.02 - VInitCell[WhichCellIsOn])) * ETFact) +  ETAdd); // estimated maximum time of charging
        C_AlarmTime[WhichCellIsOn]  = roundZeroDec(((((CBatt / CellChgCurrent) * 60) * (VCMax - 0.02 - VInitCell[WhichCellIsOn]))  * ETFactAlarm) + ETAdd); // estimated maximum time of charging then sets Alarm
        ChTimeEnd[WhichCellIsOn]=roundZeroDec(((millis()/1000)/60)+1);
        VFinalCell[WhichCellIsOn]=Vcell;  // final cell voltage
        display();
        DisconnectAllCells();
        WriteDACVOutput(DAC_InitialV);
        if (PhaseNr==1) buzzerBips(2);
        if (PhaseNr==2) buzzerBips(3);
        if (IsDEBUG) Serial.println("END,  already charged");
      }//IsAlreadyCharged==false
    }//IfPhase<2
  }//IsCharging==false

  if (WhichCellIsOn) {
    SoC[WhichCellIsOn] =  roundZeroDec(100 - ((VCMax - 0.02 - Vcell) * 100)); // state of charge in %
    ChTimeNow=roundZeroDec(((millis()/1000)/60)+1);  // now time as minutes from  power-up +1
    if ((ChTimeNow-ChTimeStart[WhichCellIsOn]) > C_OverTime[WhichCellIsOn])  IsOverTime=true;
    if ((ChTimeNow-ChTimeStart[WhichCellIsOn]) > C_AlarmTime[WhichCellIsOn])  IsALARM=true;
    TRemain[WhichCellIsOn] = roundZeroDec(((TFull * (VCMax - 0.02  - Vcell)) * ETFact) + (ETAdd * TScale));  //  estimated remaining time of charging  in minutes
  }
  lastCheckChargeMillis=millis();
}//checkCharge()

void  buzzerBips(byte n) {
  byte q=0;
  for (q=1;q<=n;q++) {
    digitalWrite(BuzzerPin,  HIGH);
    delay(100);  
    digitalWrite(BuzzerPin, LOW);
    delay(100);  
  }
}//buzzerBips()

/*  
  WARNING: before switching Relais2  ON or OFF,
  switch OFF Relais1 first, then Relais2, then Relais1 ON again if  necessary;
  This circuit KEEPS SEPARATED the battery ground from any other ground  because during balanced charging
  the pins Cells, (-) and (+), are necessarely  switched from one CELL to another, and inverted polarity at common wire!
*/
void  DisconnectAllCells() {  // ------------------------------ disconnect Cells by Relais
  digitalWrite(Relais1ConnectCellsPin, Set_OFF);
  delay(1000);
  digitalWrite(Relais2SwitchCellsPin,  Set_OFF);
  delay(1000);
  WhichCellIsOn = 0;
}//DisconnectAllCells()

void  ConnectCell_N(byte c) {  // ----------------------------- connect Cell by Relais
  switch (c) {
    case 1:
      digitalWrite(Relais1ConnectCellsPin, Set_OFF);
      delay(1000);
      digitalWrite(Relais2SwitchCellsPin, Set_OFF);
      delay(1000);
      digitalWrite(Relais1ConnectCellsPin, Set_ON);
      delay(1000);
    break;
    case 2:
      digitalWrite(Relais1ConnectCellsPin, Set_OFF);
      delay(1000);
      digitalWrite(Relais2SwitchCellsPin, Set_ON);
      delay(1000);
      digitalWrite(Relais1ConnectCellsPin,  Set_ON);
      delay(1000);
    break;
  }
  WhichCellIsOn = c;
}//ConnectCell_N()

void  WriteDACVOutput(float v) {  // ------------------------- write DAC
  SetVOutput  = v;
  SetDAC = ((SetVOutput - 1.25 + 0.75) * (4095.0 / 5.0));  // (Vdac - VdacADD  + Vdiod) * (Res / Vref)
  DAC.setVoltage(SetDAC, false);
  delay(1000);
}//WriteDACVOutput()

void  display() {  // ---------------------------------------- display LED status
  digitalWrite(RGBledBluePin[WhichCellIsOn],LOW);
  digitalWrite(RGBledRedPin[WhichCellIsOn],LOW);
  if (IsALARM==true) {
    blink_redALARM();
  } else {
    if (IsAlreadyCharged==false)  {
      if ((IsCharging==true)) {
        if (IsOverTime==false) {
          if  (SoC[WhichCellIsOn] <= 20) blink_red();
          if (SoC[WhichCellIsOn] > 20  && SoC[WhichCellIsOn] <=40) blink_red_purple();
          if (SoC[WhichCellIsOn]  > 40 && SoC[WhichCellIsOn] <=60) blink_purple();
          if (SoC[WhichCellIsOn]  > 60 && SoC[WhichCellIsOn] <=80) blink_purple_blue();
          if (SoC[WhichCellIsOn]  > 80 && SoC[WhichCellIsOn] <=90) blink_blue();
          if (SoC[WhichCellIsOn]  > 90) blink_slowblue();
         } else {
          blink_quickblue();  //overtime  warning
        }//over
       } else {
        steady_red();  //deciding  what to do
      }//charging
     } else {
      steady_blue();  //charged  
    }//already
  }//IsALARM
}//display()

void readVAvalues() {  // ---------------------------------- read V, A, values
  float n=0;
  float  s=0;
  float VCmem=0;
  float VOmem=0;
  int x=0;
  for (x=1;x<=100;x++)  {  // x nr. of readings as average filter
    n = analogRead(VcellPin);
    s  = ((5.0 * n) / 1023);  // from cell
    VCmem=VCmem+s;
    n = analogRead(VoutPin);
    s = ((5.0 * n) / 1023);  // from LM317
    VOmem=VOmem+s;
  }
  s=(VCmem/(x-1));
  Vcell = (s + ((s * 1.40) /100));  // +- % arbitrary correction (not active if  = 0.00)
  Vcell = roundThreeDec(Vcell);
  s=(VOmem/(x-1));
  Voutput =  (s + ((s * 1.40) /100));  // +- % arbitrary correction (not active if = 0.00)
  Voutput = roundThreeDec(Voutput);
  s=(Voutput-Vcell);
  Vload = roundThreeDec(s);
  n=(Vload/Rload);
  Aload = roundThreeDec(n);
}//readVAvalues()

void  readTemperatures() {  // --------------------------------- read temperatures
  int n=0;
  n = analogRead(TMP36_BatteryPin);
  TempBattery = (((5.0 * n)  / 1023) - 0.500 ) * 100;  // (-500mV=offset) 0 to 500 = below zero values
  TempBattery  = roundZeroDec(TempBattery);
  n = analogRead(TMP36_7812Pin);
  Temp7812 =  (((5.0 * n) / 1023) - 0.500 ) * 100;
  Temp7812 = roundZeroDec(Temp7812);
  n = analogRead(TMP36_317Pin);
  Temp317 = (((5.0 * n) / 1023) - 0.500 ) * 100;
  Temp317 = roundZeroDec(Temp317);
  if ((Temp7812 < HighTRegL) && (Temp317 <  HighTRegL) && (TempBattery < HighTBatL)) {  // current
    IsSlowDown = false;  // will normal chg current
  }
  if ((Temp7812 > HighTRegH) || (Temp317  > HighTRegH) || (TempBattery > HighTBatH)) {
    IsSlowDown = true;  // will  decrease chg current
  }
  if (IsALARM==false) {
    if ((Temp7812 < FanTRLow)  && (Temp317 < FanTRLow) && (TempBattery < FanTBLow)) {  // fan
      analogWrite(FanPWMPin,  FanSpeed[0]);  // Fan normal temperatures
      WhichFanSpeedIsOn=FanSpeed[0];
    }
    if ((Temp7812 > FanTRHigh) || (Temp317 > FanTRHigh) || (TempBattery  > FanTBHigh)) {
      analogWrite(FanPWMPin, FanSpeed[1]);  // Fan high temperatures
      WhichFanSpeedIsOn=FanSpeed[1];
    }
    if ((Temp7812 > RegulatorTAlarm)  || (Temp317 > RegulatorTAlarm) || (TempBattery > BatteryTAlarm)) {  // ALARM
      IsALARM = true;  // will STOP charging etc.
      analogWrite(FanPWMPin,  FanSpeed[2]);  // Fan ALARM temperatures
      WhichFanSpeedIsOn=FanSpeed[2];
    }
   } else {
    analogWrite(FanPWMPin, FanSpeed[2]);  // Fan ALARM
    WhichFanSpeedIsOn=FanSpeed[2];    
  }
}//readTemperatures()

void  blink_red() {  // ----------------------------------------- led
  delay(500);
  digitalWrite(RGBledRedPin[WhichCellIsOn], HIGH);
}
void blink_redALARM()  {
  digitalWrite(RGBledRedPin[1], LOW);
  digitalWrite(RGBledRedPin[2], LOW);
  digitalWrite(RGBledBluePin[1], LOW);
  digitalWrite(RGBledBluePin[2], LOW);
  delay(100);
  digitalWrite(RGBledRedPin[1], HIGH);
  delay(100);
  digitalWrite(RGBledRedPin[1],  LOW);
  digitalWrite(RGBledRedPin[2], HIGH);
  delay(100);
}
void blink_blue()  {
  delay(500);
  digitalWrite(RGBledBluePin[WhichCellIsOn], HIGH);
  delay(500);
}
void  blink_purple() {
  delay(500);
  digitalWrite(RGBledRedPin[WhichCellIsOn],  HIGH);
  digitalWrite(RGBledBluePin[WhichCellIsOn], HIGH);
  delay(500);
}
void  blink_red_purple() {
  delay(500);
  digitalWrite(RGBledRedPin[WhichCellIsOn],  HIGH);
  delay(1000);
  digitalWrite(RGBledBluePin[WhichCellIsOn], HIGH);
  delay(500);
}
void blink_purple_blue() {
  delay(500);
  digitalWrite(RGBledRedPin[WhichCellIsOn],  HIGH);
  digitalWrite(RGBledBluePin[WhichCellIsOn], HIGH);
  delay(1000);
  digitalWrite(RGBledRedPin[WhichCellIsOn], LOW);
  digitalWrite(RGBledBluePin[WhichCellIsOn],  HIGH);
  delay(500);
}
void blink_slowblue() {
  delay(1000);
  digitalWrite(RGBledBluePin[WhichCellIsOn],  HIGH);
  delay(2000);
}
void blink_quickblue() {
  delay(100);
  digitalWrite(RGBledBluePin[WhichCellIsOn],  HIGH);
  delay(100);
}
void steady_blue() {
  digitalWrite(RGBledBluePin[WhichCellIsOn],  HIGH);
}
void steady_red() {
  digitalWrite(RGBledRedPin[WhichCellIsOn],  HIGH);
}

void ledShow() {  // --------------------------------------------  initial show & Fan
  digitalWrite(RGBledBluePin[1], HIGH);
  digitalWrite(RGBledRedPin[1],  LOW);
  digitalWrite(RGBledBluePin[2], LOW);
  digitalWrite(RGBledRedPin[2],  LOW);
  delay(500);
  digitalWrite(RGBledBluePin[1], HIGH);
  digitalWrite(RGBledRedPin[1],  HIGH);
  digitalWrite(RGBledBluePin[2], LOW);
  digitalWrite(RGBledRedPin[2],  LOW);
  delay(500);
  digitalWrite(RGBledBluePin[1], LOW);
  digitalWrite(RGBledRedPin[1],  HIGH);
  digitalWrite(RGBledBluePin[2], LOW);
  digitalWrite(RGBledRedPin[2],  LOW);
  delay(500);
  digitalWrite(RGBledBluePin[1], LOW);
  digitalWrite(RGBledRedPin[1],  LOW);
  digitalWrite(RGBledBluePin[2], HIGH);
  digitalWrite(RGBledRedPin[2],  LOW);
  delay(500);
  digitalWrite(RGBledBluePin[1], LOW);
  digitalWrite(RGBledRedPin[1],  LOW);
  digitalWrite(RGBledBluePin[2], HIGH);
  digitalWrite(RGBledRedPin[2],  HIGH);
  delay(500);
  digitalWrite(RGBledBluePin[1], LOW);
  digitalWrite(RGBledRedPin[1],  LOW);
  digitalWrite(RGBledBluePin[2], LOW);
  digitalWrite(RGBledRedPin[2],  HIGH);
  delay(500);
  digitalWrite(RGBledBluePin[1], LOW);
  digitalWrite(RGBledRedPin[1],  HIGH);
  digitalWrite(RGBledBluePin[2], LOW);
  digitalWrite(RGBledRedPin[2],  HIGH);
  analogWrite(FanPWMPin, FanSpeed[1]);  // Fan high temperatures test
  delay(5000);
  analogWrite(FanPWMPin, FanSpeed[0]);
}//ledShow()

void  serialPrintChg(const char msg[]) {  // -------------------------------- print charging
  Serial.print(msg);
  Serial.print(":");
  Serial.print(" Cell=");
  Serial.print(WhichCellIsOn);
  Serial.print(" Vdac=");
  Serial.print(SetVOutput,3);
  Serial.print(" Vcel=");
  Serial.print(Vcell,3);
  Serial.print(" Acel=");
  Serial.println(Aload,3);
}

void serialPrintDebug() {  // -----------------------------------------------  print debug serial & bluetooth
  Serial.print("TBatt=");  // temperatures
  Serial.print(TempBattery,0);
  Serial.print(" T7812=");
  Serial.print(Temp7812,0);
  Serial.print(" T317=");
  
  Serial.print(Temp317,0);
  Serial.print("  Fan=");
  Serial.print(WhichFanSpeedIsOn);
  Serial.println("/255");

  Serial.print("Cell=");  // VA values
  Serial.print(WhichCellIsOn);
  Serial.print("  VCel=");
  Serial.print(Vcell,3);
  Serial.print(" Vdac=");
  Serial.print(Voutput,3);
  Serial.print(" ACel=");
  Serial.println(Aload,3);

  Serial.print("IsAlrdy=");  // status
  Serial.print(IsAlreadyCharged);
  Serial.print(" IsCharg=");
  Serial.print(IsCharging);
  Serial.print(" IsOver=");
  Serial.print(IsOverTime);
  Serial.print(" IsALRM=");
  Serial.print(IsALARM);
  Serial.print(" IsSlow=");
  Serial.println(IsSlowDown);

  Serial.print("Start[1]=");  // charging  times [1]
  Serial.print(ChTimeStart[1]);
  Serial.print(" End[1]=");
  if (ChTimeEnd[1] > 0) {
    Serial.print(ChTimeEnd[1]);
  } else {
    Serial.print("?");
  }
  Serial.print(" Time[1]=");
  if (ChTimeEnd[1] > 0) {
    Serial.print(long(ChTimeEnd[1]  - ChTimeStart[1]));
  } else {
    Serial.print("?");
  }
  Serial.print("  VInit[1]=");
  Serial.print(VInitCell[1],3);
  Serial.print(" VFinal[1]=");
  Serial.print(VFinalCell[1],3);
  Serial.print(" Over[1]=");
  Serial.print(C_OverTime[1]);
  Serial.print(" Alarm[1]=");
  Serial.print(C_AlarmTime[1]);
  Serial.print("  Remain[1]=");
  Serial.print(TRemain[1]);
  Serial.print(" SoC%[1]=");
  Serial.println(SoC[1]);

  Serial.print("Start[2]=");  // charging times  [2]
  Serial.print(ChTimeStart[2]);
  Serial.print(" End[2]=");
  if  (ChTimeEnd[2] > 0) {
    Serial.print(ChTimeEnd[2]);
  } else {
    Serial.print("?");
  }
  Serial.print(" Time[2]=");
  if (ChTimeEnd[2] > 0) {
    Serial.print(long(ChTimeEnd[2]  - ChTimeStart[2]));
  } else {
    Serial.print("?");
  }
  Serial.print("  VInit[2]=");
  Serial.print(VInitCell[2],3);
  Serial.print(" VFinal[2]=");
  Serial.print(VFinalCell[2],3);
  Serial.print(" Over[2]=");
  Serial.print(C_OverTime[2]);
  Serial.print(" Alarm[2]=");
  Serial.print(C_AlarmTime[2]);
  Serial.print("  Remain[2]=");
  Serial.print(TRemain[2]);
  Serial.print(" SoC%[2]=");
  Serial.println(SoC[2]);
  
  Serial.print("TimeNow=");
  Serial.println(ChTimeNow);

  lastPrintDebugMillis=millis();
}//serialPrintDebug()

// round zero decimal  // ----------------------------------------------- rounds
float roundZeroDec(float  f) {
  float y, d;
  y = f*1;
  d = y - (int)y;
  y = (float)(int)(f*1)/1;
  if (d >= 0.5) {
    y += 1;
   } else {
    if (d < -0.5) {
      y  -= 1;
    }
  }
  return y;
}
// round three decimals
float roundThreeDec(float  f) {
  float y, d;
  y = f*1000;
  d = y - (int)y;
  y = (float)(int)(f*1000)/1000;
  if (d >= 0.5) {
    y += 0.001;
   } else {
    if (d < -0.5) {
      y  -= 0.001;
    }
  }
  return y;
}

Downloadable files

Charger schematic diagram (Fritzing)

PCB bottom (small LED board)