Wi-Fi programmable room thermostat with air quality monitor

1inary file (no preview

1<?php
2// Wi-Fi programmable room thermostat with air quality monitor
3//  cadil@ukr.net
4// test -  http://skorovoda.in.ua/php/aqm42.php?mymail=my_login@my.site.net&t=22.2&h=55&co2=666
5$EMAIL=0;
6$TEMPER=0;
7$vlaga=0;
8$carbon=0;
9$device=0;
10$EMAIL=$_GET["mymail"];
11$device=$_GET["ID"];
12echo  $EMAIL;
13$TEMPER=$_GET["t"];
14$vlaga=$_GET["h"];
15$carbon=$_GET["co2"];
16$mdate  = date("H:i d.m.y");
17echo <<<END
18<p>Temperature:  $TEMPER °С<p>
19<p>Humidity:  $vlaga %<p>
20<p>Carbon dioxide content:  $carbon ppm<p>
21<p>--------------------<p>
22<p>Meteostation:  $device<p>
23END;
24echo <<<END
25<p>$mdate</p>
26END;
27mail($EMAIL, "Air  Quality Monitor " .$device. " v.051018","   This message was generated automatically  by air quality monitor " .$device.    "One or more room air parameters (temperature,  humidity or carbon dioxide content) are outside the specified limit values. ===  Temperature: ".$TEMPER."°C === "."Humidity: ".$vlaga."% === "."Carbon dioxide  content: ".$carbon." ppm === "."Analyze the information! === Date: ".$mdate,"From:  my_sensors@air-monitor.info \
28")
29
30?>

1/*
2Wi-Fi programmable room thermostat with air quality monitor
3Contactor
4
5  */
6
7#include <RCSwitch.h>     // https://github.com/sui77/rc-switch
8RCSwitch
9  mySwitch = RCSwitch();
10
11void setup() {
12      pinMode(13, OUTPUT);
13      pinMode(3,
14  OUTPUT);
15      pinMode(4, OUTPUT);
16      pinMode(5, OUTPUT);
17      pinMode(6,
18  OUTPUT);
19
20      digitalWrite(3, HIGH);
21      digitalWrite(4, HIGH);
22
23      digitalWrite(5, HIGH);
24      digitalWrite(6, HIGH);
25      digitalWrite(13,
26  LOW);
27
28      mySwitch.enableReceive(0);
29    }
30
31void loop() {
32
33       if( mySwitch.available() ){
34        int value = mySwitch.getReceivedValue();
35
36
37              //t < Tmin
38        if(value == B11111110) digitalWrite(4, LOW);
39
40        else if (value == B10000000) digitalWrite(4, HIGH);
41
42                //co2
43  > Cmax  
44        if(value == B11111101) digitalWrite(5, LOW);
45        else
46  if (value == B00000010) digitalWrite(5, HIGH);
47
48             //h < Hmin
49
50        if(value == B11111011) digitalWrite(6, LOW);
51        else if (value ==
52  B00000100) digitalWrite(6, HIGH);
53
54            //t > Tmax
55        if(value
56  == B11110111)digitalWrite(3, LOW);
57        else if (value == B00001000) digitalWrite(3,
58  HIGH);
59
60        // LED D13 Arduino - indicates the presence of a transmitter-receiver
61  connection (blinks - there is a connection)
62        if(value == B10101010) digitalWrite(13,
63  HIGH);  //  B10101010 - transmitter enabled code, generated in the analyzer without
64  conditions 
65        else  digitalWrite(13, LOW); 
66
67        mySwitch.resetAvailable();
68
69  }
70}